hi everybody!I just want to know if there is any relation between the hello timer and max age in stp. Does descreasing the hello timer will also decrease the max age timer which in turn decrease the time to discover dead neighbor?thanks a lot!
hi everybody!I just want to know if there is any relation between the hello timer and max age in stp. Does descreasing the hello timer will also decrease the max age timer which in turn decrease the time to discover dead neighbor?thanks a lot!
it's probably a very basic question, but i have never done it. we are changing ISP's and all of the NAT configurations have to change on my ASA 5520. So instead of going through each button and option on the ASDM GUI- i thought it would be faster to ...
I'm trying to configure my router to use the switch ports route through the default route. when I plug in a server and try to ping the gig0/0 I cannot. The router is an internet router, I need to put some devices outside my protected network, and wan...
Hello folksI am trying to log any kind of message thrown by Catalyst 6500 switch as well as want to log all the logging session of a user. I have little idea of configuring syslog server but no idea about configuring syslog or any log server in cisco...
We currently have all our catos accepting both SSH and telnet sessions . We need to turn off telnet now . For most except our distr. boxes we do not have any permit lists applied. What is required on catos to shut off telnet for both boxes that ...
I'm enabling DHCP snooping on a 4506 running 12.2(25)EWA4Snooping appears to be working, the binding table is propagated, and clients can receive ip addresses via DHCP. Rouge DHCP packets are blocked as designed.However, the client PXE boot process ...
I have 2 x SDSL lines (from the same ISP) and 2 x 2800 routers- these terminate with Site2Site vpn tunnels to an ASA.Does anybody know how best to configure these to utilise both lines at the same time and maybe have some resilience as well.many than...
Hi,We have been trying unsuccessfully to get a MetroE link to a remote site via the service provider to work. This link had been working when the connection between our Cat2960 switches and the telco's Alcatel 7250 at both ends was through access mod...
Hi allI created today a new transparent context on my FWSM (3.2(6)) which is in a 6509 with IOS in the slot 9.Here my configuration: firewall multiple-vlan-interfacesfirewall module 9 vlan-group 1,firewall vlan-group 1 30,[others-removed]1030!vlan 1...
We're currently trialling implementing Microsoft Office Communication Server and are struggling with implementing QOS on our 2950's. How best can we implement QOS on our 2950's to support OCS?Any help would be much appreciated.Thanks
On my router 7609, I've these modules as follows:slot3: SFM 16 port 1000mb GBICslot4: 48 port 10/100mb RJ45slot5: Sup engine 720slot7: SFM 48 port 10/100mb RJ45slot8: 8 port 1000mb GBIC enhanced QoSslot9: CEF720 4 port 10G EthernetSo, as you see, I c...
HelloIf my trunk is in use between two switch, if I use the add command to add another vlan allowed in the trunk, Is there a cutoff network?
Hello, I would like to know if is possible to upgrade a Catalsyst 4500 with supervisor engine II with CatOS to IOS system, and what is the procedure. Can we load an IOS software with supervisor engine II?
An old 2521 router displays RouterB(boot)#. What is with the 'boot'?
friends, Eigrp will have "Six" entries in routing table for same destination,Default is "four", set to "one" to disable load balancing, if that is the case, why load balacing needs to be disabled, its good in case of link failure when the primary rou...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-16-2024 12:15 PM | ||
10-15-2024 03:13 AM | ||
10-14-2024 02:50 AM | ||
10-09-2024 11:22 AM | ||
10-08-2024 08:34 PM |
User | Count |
---|---|
8 | |
8 | |
6 | |
6 | |
6 |