Switching

HiWhat's 0xC1 in configuration register?Thanks

I will soon need to move a WS-X4232-L3 from a powered up 4006 to a 4506 (w/Sup2).Can I do this while both units are powered on? When i install the WS-X4232-L3 into the 4506, will it still have the same config file as before?Any other caveats?Oh, and...

Hi everyone,I have the question about the output of "show ip dhcp binding".Cisco 2821 IOS 12.4(19) is running as IOS DHCP Server.The following is the configuration of DHCP on the C2821 and the output of "show ip dhcp binding" (paste only the pertinen...

Poe was working fine until this weekend. The ports work fine, but no poe on 3 out of 4 6548 blades. 3 works fine, but 2,4 and 9 has no poe. Show power is indicating everything is ok. We have moved one 6548 blade to a vacant slot. Trouble followe...

Hi All,I have two routers (RTA & RTB) with HSRP configured. Both routers has a serial connection to the ISP network. Preempt and tracking are enabled on both routers.RTA has a priority of 115RTB has a priority of 100Default decrement value of 10If se...

Is there a command to copy everything in flash to tftp? I have a couple dozen files in flash (for CCME) and would like to not spend a day backing it all up.Thanks,-Shikamaru

HiOn the 2 x 3750G callapsed core/distribution switches I have configure SVI interfaces for each vlan in my network (6 vlans, 1, 10, 20, 30, 40, 50). I have about 5 switch blocks/stacks each using a different vlan eg. switch_block 1 (5 x switches in...

Hi all,I think we have a problem with our switch network. Every node on the network is receiving more then one stp message in a two second period. I have tried setup a switch to be the root for all vlans, and then set the hello time to 10 sec. The...

Can any one provide me L3 switching configuration of L3 switching Lab consist of A router, a L3 switch, L2 switch and number of hosts.It should also have inter Vlan routingI would be thankful if any one would provide me this,.

Setting up a simple multicast. The 4500 has the "ip multicast-routing" command on. All vlans have the "ip pim sparse-mode" and are located on the core.The vlans are then trunked out throught the gig interfaces to the edge 3750 switches. The 3750 swit...

HiIm using 2 x 3750G switches as callapsed core/distribution switches. I have 6 Vlans (1, 10,20,30,40,50) that will be assigned per switch block.Switch block 1This will have 5 switches in the block connected at the top switch via fibre trunk to core...

Hi All,we are having multiple VLANs in our infrastructure. for all the VLANs except 1 vlan when we ping the brodcast IP of that vlan pool, we get a reply from the gateway ip of the VLAN. But only for 1 vlan we are getting very wierd behaviour. for th...

Hi, I have the setup of 8, 3750G-24ps switches, in a stack(using stack cable). IOS 12.2(44)se1(c3750-advipservicesk9-mz.122-44.SE1.bin), is installed in all switches. Nortel class 3 IP phones are connected to all the ports which required 15.4 watt ...

I have a Cisco 1841 router with an ADSL card (WIC-1ADSL-DG) and I recently added an etherswitch card (HWIC-4ESW). The problem that I'm having is that any device connected to the etherswitch card can't see my network. I want to find a way to connect...