Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...

Hi,A quick question. Do you see 01-00-0c-cc-cc-cc system MAC address as being broadcast or multicast?I can find arguements to both, but I am interested to hear more opinions.Thanks,David

dknov by Level 3
  • 19997 Views
  • 3 replies
  • 0 Helpful votes

Resolved! Vlan overlapping

hi all,i have three vlan as mentioned below- int vlan 80 ip add 10.101.108.129 255.255.255.224int vlan 90 ip add 10.101.108.161 255.255.255.224int vlan 100ip add 10.101.108.193 255.255.255.224my prob is i want to delete this two vlan 90 & 100 and wa...

network by Level 1
  • 1396 Views
  • 2 replies
  • 0 Helpful votes

Hi All,I am working on a new network configuration for our company and I'm not sure if I have the right equipment to do what I'm wanting to do. We just got a direct allocation of IPs directly from ARIN and we're setting them up.Here's the equipment ...

Resolved! VLSM

Hi,I have a confusion with regard to VLSM. I have read, during my degree, that in order to do VLSM, we should start from the top (i.e. the highest number of hosts required). However,i have also seen cases (Cisco Dumps particularly), where they have s...

I have discovered a problem with my newotk on one particular vlan. The problem startedwith a dhcp issue. No clients whatsoever could get a ip address from vlan2 on the switch,but there were no problems with the other vlans. The router itself acts as ...

frkainvid by Level 1
  • 1285 Views
  • 4 replies
  • 0 Helpful votes

hi everybody!i just want to know if two switches sw1 and sw2 are connected as:sw1---------------------sw2 f0/1 f0/2will the trunk form if sw1 is configured as:sw1(config-if)switchport mode dynamic autosw2 is configured as:sw2(config...

sarahr202 by Level 5
  • 573 Views
  • 1 replies
  • 0 Helpful votes

I need help temp setting up to allow multicasts through my PIXs at my remote sites. Basically here's what I need:I am using Altiris Deployment Console for HP Thin Clients and all thin clients are setup to find the deployment console server through mu...

I am sure this has been asked but I can't seem to find it and need to be sure. From what I have read it is NOT possible to create an etherchannel from a single server with one connection each to two different 6509 chassis. No VSS SUP or any 10G port...

Hi All,My access switch has just rebooted automatically. What command should I use to find out the cause of the incident aside from show logs, show diagnostic?I need the data to provide to TAC.Thanks,Allen

ellendrew by Level 1
  • 724 Views
  • 2 replies
  • 0 Helpful votes

The loggs below is from my core.. the port bening refered to is my route switch moudle. should i change the trunking mode to DOT1Q. It is currently on ISL2008 Jul 23 15:52:19 PDT -07:00 %PRUNING-6-TRIGJOIN:trunk 15/1- send trig Join2008 Jul 23 15:5...

ougwuoke by Level 1
  • 1211 Views
  • 6 replies
  • 0 Helpful votes

I have a Cisco 1801 router connected to the Internet configured wit NAT. An outbound service-policy is configured on the public interface to prioritise an application which is working.I want to prioritise traffic from one of my wireless clients also...