Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...
Forum Posts
Resolved! Routing based on intefaces
Hi Guys,I am wondering if we can create routes based on the interface through which the traffic is received. Please refer to the below diagram of the network. So, what I want to achieve is, that when any traffic is received by the switch on the inter...
Resolved! incorrect time in log file
we have several cisco switches. we have NTP setup running on a msfc of a 6500. switches are set to get time from 6500. the show clock command on the switches show the correct time. But when something is put in the log file of the switch,the time ...
Hi Folks,If my switch is in the below licensing state, can i get away with not activating it with my smart account / SSM ? Looks like it's all "in use" but unregistered...will there be any issues in both short and long term ??Smart Licensing Status==...
Resolved! Cisco TDR question
Good morning,I have a little understanding how Cisco cable-diagnostics TDR works, but I had a simple question. I have an AP that is using PoE on port 27, and when I run the test is say 55 which I assume that means 55m away? Should that be a concern...
How will you find out Uplink in L2 switches
Resolved! Nexus 9232C ports functionality
Hi, I've been using, testing and updating Nexus switches for a few years now but this problem has me stumped. I have several N9K-C9232Cs. Plan is to do a basic functionalty test, update them and deploy.They are currently running NXOS 9.3.9 and are in...
I know it stands for Enhanced Address Recognition Logic. any good documentation about it?
Hi I have a 10G nexus 3524x: switch# show version Cisco Nexus Operating System (NX-OS) Software TAC support: http://www.cisco.com/tac Documents: http://www.cisco.com/en/US/products/ps9372/tsd_products_support_series_home.html Copyright (c) 2002-2016,...
Hi,I am new to networking. Need to configure syslog server to switches. Could anyone please help what information and commands needed to configure that? Thanks!
Resolved! [Catalyst 1000 Series] Flexlink Function
Hi all, Currently, Catalyst 1000 Series with version 15.2(7)E not support Flexlink function, but does it support Flexlink+?I've try to add Flexlink+ command on this model not success, the error displayMain port:interface GigabitEthernet1/0/1switchpor...
Hito enable Wake on LAN on 802.1x enabled ports the settingaccess-session control-direction both | inmust be used. From the descriptions it seems to be clear that the option in must be used, so that the switch can forward the magic packet to the devi...
There are 5 C9200 switches operating as a stack running IOSXE Version 16.9.3:- when making any configuration changes and type write memory command the stack shows the below log and then reboots with no any configuration change. Log: 001479: Jan 15 ...
Resolved! Cisco 6880-X-LE No VSLOTs Left?
I am trying to create a new fiber extension off of my 6880 X LE catalysts but the fex is stuck at "Registration" and the logs show: %FEXMGR-SW1-3-FEXMGR_MAX_VSLOT_ALLOC: No VSLOTs are left for new module to allocate. Enable Temp VSLOT to allow 'renum...
#Help I have recently upgraded our cisco 4507 switches from IOS "Cisco IOS XE Release 3.8.6E". to " Cisco IOS XE Release 3.11.6E". After upgrade Avaya 4625 and Avaya 9600 series phones stoped reaching TFTP and utility servers. There is no config ...
Hello,I want to upgrade 6880-x-le VSS switches from 152-1.SY4 to 155-1.SY8. My plan is to upload the new software to both switches and use the "reload" command.there is one thing that I am not sure of and that is the ROMMON. The current version is ...
