Switching

Hi GuysNeed some clarification on this. We have 2 subnets in a VLAN 10 e.g. 1.1.1.0/24 and 2.2.2.0/25.Now we want to sepaarate out these vlans like1.1.1.0/24 in Vlan 10 and2.2.2.0/25 in Vlan 20.But my thoughts is that for us to be able to physically ...

Hi NetPro,anyone knows what is the logs stand for ?%RMON-5-RISINGTRAP: Rising trap is generated because the value of etherStatsEntry.4.16 exceeded the rising-threshold value 1750000000%RMON-5-FALLINGTRAP: Falling trap is generated because the value o...

I can successfully provision a switch offline by configuring the priority and switch number. I can also add the switch to the stack without any hassles. However, I'd like to know if it's possible to provision the switch offline, configure port settin...

We have two Catalyst 2960 switches showing high buffer loss. The site is under heavy utilization, so we want to eliminate all possible issue. Here is the switch status:System image file is "flash:c2960-lanbase-mz.122-25.SEE3The below buffer status is...

My topology looks like this:Cox cable internet cloud -> Motorola Cable modem -> [e0] 2501 router [s0] -> [s0] 2501 router [e0] -> 2924 switch -> hostMy mission is get connect to the internet. But its been all fails so far. The e0 port on the 2501 rou...

Hi There;Does anyone know the Australian phone number for pre sales design support.Regards

Hello I am currently running my 6513 at 110V with a max of 3000Watts. I need to install more blades upgrade power source to 220V to take advantage of the 6000 Watts capability. Now will I have 6000watts in redundant mode or combine?ho power system p...

I downloaded a new catOS, version 8.5.7 for a 6509 and Im running bootstrap version 7.1.1. I added a prepend boot variable statement for the new code but the switch will not come up on the new code, only the old code.Has anyone experienced this????TH...

I have a strange problem and I don't know if it is specific to the Windows Vista operating system or my network configuration. Here is my scenario, I have 2 Windows Vista Ultimate clients that causes all other users on the network to not be able to ...

Hi,Vlan 23 and 28 are trunked between Cisco 4500 and Cat 3750. On the Cisco 4500, these 2 vlans are available on the "Vlans in spanning tree forwarding state and not pruned" on sh int trunk. However, on the Cat 3750 these vlans does not appear on "...

Hello,I have a 3750G which has got a high CPU (up to 40%), mostly at interrupt level (41%/28%).I think the problem comes from IP packets that are processed instead of beeing hardware switched. ROUTER#sh platform ip unicast failed routeTotal of 0 cove...

HiReply from10.10.10.250: bytes=32 time<1ms TTL=255Reply from10.10.10.250: bytes=32 time<1ms TTL=255Reply from10.10.10.250: bytes=32 time<1ms TTL=255Reply from10.10.10.250: bytes=32 time<1ms TTL=255Reply from10.10.10.250: bytes=32 time<27ms TTL=255Re...

I have a 24-port Catalyst 3560G that is providing power to a dozen or so IP phones. I recently unplugged one of the phones and when I went to go plug it back in the power wouldn't resume. I tried replacing the phone, no power. I tried plugging both...

Hi,whenever i try to connect to cisco switch 4506 using Cisco Network Assistant, i get the message unsupported device !i have enabled : ip http server on the 4506 switch and still not able to connect to it using CNA.i have 2950 and 2970 and able to ...

Hello,I would like to know if it is possible to configure two Vs-S720 inside a unique chassis with SSO redundancy but without the VSL link and the VSS application ?In fact, are we able to use this new supervision card like the Ws-SUP720-3B ?Thanks a ...