We are having two servers with some services configured for load balance.How i can see specific server load on CSS or i want to see how much load is on server1 and server2.Which command will give this output?
We are having two servers with some services configured for load balance.How i can see specific server load on CSS or i want to see how much load is on server1 and server2.Which command will give this output?
Hello.I have 2 switches, a 2950 & a 2900XL.Here is the config for port 24 on both:SW2900XL#sh int fa0/24 swName: Fa0/24Switchport: EnabledAdministrative mode: static accessOperational Mode: static accessAdministrative Trunking Encapsulation: islOpera...
ROUTER1|(172.31.11.4/24, Serial1/0.1, OSPF Area 0, Point-to-Multipoint)|||Frame Relay Cloud----------(172.31.11.2/24, Serial1/0.1, OSPF Area 0, Point-to-Multipoint) ROUTER2||||(172.31.11.1/24, Serial1/0.1, OSPF Area 0, Point-to-Multipoint)ROUTER3 (10...
I need help to configure HTTPS on a swict 2950T
Sorry helping out a friend here. I was wondering if anyone can suggest a router that would be good enough to support a small business network. The network has 4 subnetworks. We have four switches these are Cisco Catalyst 2960-24TT 24 port Switch. I w...
I just upgraded the IOS on my catalyst 2948G switch to 6.4(21). Part of the configuration is that the console, telenet, and http session are all enabled on both login authentication and enable authentication. I can get to the switch through console...
I have these cards in a distribution Cat6500: WS-X6348-RJ-45I know that they are quite old and that they do not have a priority queue (Rx: 1q4t Tx:2q2t) However could we configure a basic QoS strategy? May be we could configure one output queue for v...
hello!when you configure GLBP ON THE interface vlan.do we need to configure no ip proxy-arp?it works without this command as well as this command also:no ip redirects
Hi all,I wanted to know the command for disabling port security on a v12 IOS switch.Thanks all.
I am unable to create sub-interfaces on a 3750E running 12.2(35)SE2 (on a gig ethernet interface). Has anyone succesfully done so?
(this is dup. of a message that I posted in the WAN forum, but perhaps this is a better forum to ask in...) I have two routers, one with a public IP (xxx.xx.xx.23) WAN port and the second one with a private IP connected up to the first router. I want...
I'm trying to set up a vlan that will allow me to connect a device in one part of the building to a router in another. The switch at the far end is a 3550 and I think I have set vlan ok on that one. However I'm having trouble setting up the vlan on...
I create a VLAN interface in Layer-3 Switch and configure multicast traffic over this VLAN. But the multicast traffic is always duplicated after passing the Layer-3 Switch. I checked the throughput among devices and found that the layer3 switch recei...
Hello everyone,A question on the show processes cpu command...We have numerous WS-C3524-XL-EN switches througout the network on different subnets. When I run this command on any of the switches it says the following...CPU utilization for five second...
Hi...Can someone help me in getting the OID value for Maximum number of VLAN's supported and number of existing VLAN's configured in Switch using VTP...We are looking this specifically for Cisco 2950 series switches.Thanks...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-23-2025 01:45 PM | ||
07-08-2025 11:44 PM | ||
07-04-2025 02:13 AM | ||
06-26-2025 10:05 AM | ||
06-16-2025 07:47 PM |
User | Count |
---|---|
13 | |
11 | |
9 | |
5 | |
4 |