hello there, i'm in trouble to setting up Multicast Network on LAN could you please help me to understand multicast on Layer 2 Network. actually i have IPTV network on hotel, total i have 277 IPTV on LAN and IPTV is reside on same Subnet, i have to...
Hi, Is Cross-Stack EtherChannel or LAG supported on Cisco Business Switches CBS350? There is no info in: Configuring LAG Settings on a CBS250 or CBS350 Series Switch through the Command Line Interface (CLI)https://www.cisco.com/c/en/us/support/docs...
If I am creating an EtherChannel between the access switch and the Multilayer switch, does the mode needs to be the same?
Hi, Can Cisco CBS350 switch be able to support HSRP at a distance? someone please help.Thanks
I have a requirement to implement IP SLA on 9300 switches as shown in the diagram. Two locations are connected over FO and Radio link. My primary path should be FO and if FO fails data should go over Radio. Please advise on my IP SLA switch configura...
I'm trying to understand why this occurs and what the benefits are shutting the port down. Is it correct to think if udld is detected their is potentially a hardware issue with some strands in the fibre cable? Or sfp or switch?why would you want to ...
Hello everyone,I am trying to create a VLAN which solely purpose is to access internet. I shouldn’t allow to access other vlans on the same network.my DHCP sever is on Windows sever 2012 So I got most of the config figure out please let me if I am w...
Hello, we have a Cisco 2960-x recovered and repaired from a colleague, the switch it is turning on but it has the SYST, STAT and MAST turned on, not blinking. What can I do to make it working and reset? Thank you very much in advanced.ByeFabrizio Ron...
Dear GentsI need to know all details of Packet Life Cycle /processing in DC switches like ( 4500 , 6500....etc) ,what tables will process that packet , what is the process engine, what is queue, I was trying to find this details but I can't could an...
HiI have 4 x 48 port switch stack of 3750x and have been tasked to split the task how would it be best to split it.SW1 IS MASTERI was thinking of moving sw3 and sw4 and make it its own stack but I have no spare ports as backup if I do it this way I w...
Hi, I have created a simple network topology with 2 switches and 1 router.switch 1 is directly connected to a router1 via fe port and a switch2 is a trunk link to switch 1.however I am unable to ping from switch 2 to router1. not sure what I did wron...
does Cisco 3750 switch support IEEE 802.1x mac-based Authentication?how to confiure mac-based Authentication
hi guys, i have a ghost story to share.. i had configured some access lists in my 3560 switch and after testing everything was working fine. then i had powered off the switch after saving the config. today when i powered it back on, i saw two...
Hi everyone,I have an issue with C3750 switch: I'm unable to Telnet/SSH and ping it directly, whether I'm using Putty or Terminal;However, I can telnet and ping it from another switch.Every required configuration for remote access has been completed ...
I have a pair of Cat9606 switches. I'm running stackwise with two links using ports on module 5 47 and 48 on each switch (4 ports, 2 links) Because of redundancy I would like to move the link on module 5 port 47 on each switch to module 1 port 48 ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 06-26-2025 12:40 PM | ||
| 06-26-2025 10:05 AM | ||
| 06-16-2025 07:47 PM | ||
| 05-27-2025 03:30 AM | ||
| 05-27-2025 12:59 AM |
| User | Count |
|---|---|
| 9 | |
| 8 | |
| 6 | |
| 5 | |
| 4 |
