Good morning,Is there any bsmart access list feature that enable me to add and delete some statement from tha ACL without impacting all the other statements?Any link on CCO.Thanks
Good morning,Is there any bsmart access list feature that enable me to add and delete some statement from tha ACL without impacting all the other statements?Any link on CCO.Thanks
I've recently purchased 2 1538M hubs, but the seller did not have the IP, or other items needed to use the Configmaker tool to get them setup.I've tried a crossover cable and no luck either. Is there a hardware way to set these to default and get the...
Can I use tftp upgrade when I am in ROMMON and need to upload the IOS?Where can I find the documentation for 3725?ThanksMatteo
I have been reading about summarizing routes and i just don't find a pattern on how that is done. Any one knows on any link where i can get more informantion on what can or can't be done when summarizing routes?Thanks for your time!
Hi, I'm a student in my first year of an IT program at a community college and we are required to design a network layout plan. I'm not quite sure how to go about doing this - we have the layout of the building, and where all the computers are locat...
I am trying to find out how to measure the utilization on a 100mb serial link between two sites that are connected with 4500 routers and 3548 switches. I can't seem to find any good documentation on the site unless I'm searching incorrectly. Thank...
Hi can someone tell me where I can get the Cisco Icons to do graphics?Thanks for your helpRegardsLp
Hi...I am using a class A range with a subnet mask of 24 for our lan. We are connected via ISDN line to another site using 1700 router. I have connected the fastethernet port of the router (10.1.1.1/24)to our core (6506) and gave the ethernet port in...
Hi guys,I am new to this list, so I apologies in advance for the stupid question.My task is to connect our network with registered IP addresses to the network with "private" IP addresses for communication between one specific host on our network with...
Hi,I have two routers connected to my LAN via switch, only one router can ping the other router. Scenario:Router A: is an internet routerRouter B: 2nd router connected to the same networkRouter A is the only one can ping router B but router B cannot ...
How do you stop broadcast traffic on this switch? 1548M
We have a couple of Cat-6506's with MSFC's etherchannelled together on which we need to create loopback interfaces. Do these interfaces have to be on a separate subnets?Thanks.
At Present I am using No-name VOIP Routers and they are working fine. Now I want to replace them with Cisco Routers to get better results. I tried to configure them with Cisco "ConfigMaker" but I am facing lots of problem. I need help. I need a basi...
I'm not sure this is a question for this forum,but i will ask anyway.I have 2 2501's,1 2502, and a 1912 switch.My problem is as follows,with my laptop setup running win2000pro,i can run hyperterminal and it comes up fine without internet connection.M...
We have a couple of Layer 3 switches (Cat-6506) that are etherchannelled together. There are 8 Vlans defined on the switches and we need to configure HSRP on the vlan interfaces. When the HSRP is configured on a vlan int, what would be the default ga...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-06-2025 12:20 PM | ||
05-06-2025 02:02 AM | ||
05-06-2025 01:05 AM | ||
04-23-2025 06:26 AM | ||
04-23-2025 06:18 AM |
User | Count |
---|---|
8 | |
7 | |
5 | |
5 | |
3 |