Hello, I am trying to get licenses from PAK I have received with BE6000 for VCS-C installed on it. SKU: CTI-VCSC-BE6K-PAKProduct Family: Cisco TelePresence VCS Control, Expressway and Starter Pack,Produsct descri...
Hello, I am trying to get licenses from PAK I have received with BE6000 for VCS-C installed on it. SKU: CTI-VCSC-BE6K-PAKProduct Family: Cisco TelePresence VCS Control, Expressway and Starter Pack,Produsct descri...
Hello, I wonder if the card mentioned in the title would work with a 2951 GW for ISDN video reception through bonded E1 channels, for example to support a 384 Kbps videoconference. We always have used 3240 GWs for this so I am not completely sure tha...
Hello, Is it possible to use SX80 as a standalone unit without any call control? Thanks in advance!
Hi Folks, I have a issue, I'm deploying in my customer the TMS 14.3 to schedule the CTS.But, when i add in TMS the Ip of CUCM, the firts 10 sec is OK, but in a few sec the TMS show the following message:#679802 - Organization Top Level Domain is not ...
Hi I am venkatesh in my comapy using cisco c40 as long time ago. but we dont no the admin user name or passwordi cant reset aslo. i take remote console in putty and hybernet also but device i not connect i connect com portserial to RJ45 is not conn...
Hi everyody.I tried to connect VCS control to EW by H.323 through default port 6001 and got message:Reason="Time difference too large for authentication"sip connection had been set sucsessfuly.What can it be? Thanks a lot.
Here is my deployment : - TMS 14.4.2- CUCM 10.5.1- Cisco Expressway-C & Cisco Expressway-E X8.2.1- Conductor XC2.3- MCU 5320 4.5 (1.45) Endpoints are registered to the CUCM. There is a SIP trunk between the CUCM and the conductor with a route pattern...
Hi ,We are planning to upgrade MCU 45XX in our environment . There are feature key installed (1080p), MCU activation, Encryption, Web conferencing...etc. I would like to know if all the keys has to be applied again after the upgrade or will it gets...
I am running J4.7.2 on my MPS800.Does any one have the procedure to create a login banner at the login browser prompt or the SSH prompt ???VRChet
I recieved a new MX300G2. When I power up it, but the device didn't startup.This MX300G2 was after a DOA MX300G2, the first MX300G2 also didn't startup.Can someone help me. Thank you.
Hi, We have a topology look like below.CTS -> CUCM -> CUBE -> VCS-e -> VCS-c -> Telepresence Server. The call search is success until Telepresence Server but the call is not connected.Hereby i attached the configuration of the CUBE to review. Version...
Hello, I am unable to find any documentation on Ports used between VCS-E neighbors. The document "Cisco TelePresence Video Communication Server (Cisco VCS) IP Port Usage for Firewall Traversal" does not list neighbor scenario.When neighbor zone is es...
Hi all, I am using Cisco MCU 5310 via Static NAT with a public IP address. When I call from the MCU to Polycom HDX6000 in internet by using a public IP address. However, I get one-way video call. I check in Call statistic and see that the Polycom HD...
I am trying to get my TelePresence ISDN Link to work in BRI mode.When I have a Tandberg call using a ISDN BRI to my TelePresence ISDN Link it only conects using the BRI Interfaces 1..4 Directory 1 Numbers.How do I get it to use the Directory Number ...
Hi,I have added two Cisco IP Communicator in CME 8.6 in Cisco 2911. What will be the configuration of gateway in order to make the video call between 2 Cisco IP communicator?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
03-26-2024 08:37 AM | ||
03-22-2024 10:12 AM | ||
03-20-2024 01:51 AM | ||
03-11-2024 05:37 PM | ||
03-06-2024 10:37 AM |