Hi, Can anyone tell me how to get the serial number of Tandberg Codec CTS-C60-K9 device.can this be located on the device and in what format is it written?Prompt response will be appreciated.Regards, Peter Nnaji.
Hi, Can anyone tell me how to get the serial number of Tandberg Codec CTS-C60-K9 device.can this be located on the device and in what format is it written?Prompt response will be appreciated.Regards, Peter Nnaji.
Hello, I had a question about the Tandberg EX90, I'm trying to connect a projector in the HDMI Out of the Tandberg, but it is not giving signal to the projector, right now, what is it setup is this for the HDMI output: xConfiguration Video Output HDM...
we have a Tandberg MXP880 video conference device in the office that we've been using for more than 3 years now with ISDN connection and sometimes through LAN. Accepting video calls from one of our site in Japan is okay and having a 3 way video confe...
Im looking at the pros/cons when setting up CUCM 8.6 h323 or SIP trunk to Polycom CMA. Basically, I have a Polycom eviroment with different endpoints such as different V series endpoints (personal and conference room). I have CUCM 8.6 with diffe...
I am trying to get the CUCM directory to work on my EX60/EX90 endpoints. I am running TC5.0 on my end points and they are registered to a VCS. I have tried changing the phone book on the endpoints to use CUCM and I put in the standard directory URL...
I have several Cisco 7961G phone's that I'm trying to get setup with a CCM located in a separate geographical location. The CCM is attempting to push the SCCP 9.2.1 update to the phones which was taking forever and a day due to slow link connectivity...
Hi guys,a security audit (also in the video environment) brought up a "small risk" regarding SSL / TLS Renegotiation Handshakes on a VCS Expressway (X7.1).This VCS-E is a dual network port installation and the audit result relates to the test which w...
Dear All,I tried to call an End-Point (104@gatekeeper IP), message of (Gatekeeper Resources) seen, and call disconnected.please, help me to know what this message refers to.ThanksOmar Mahmoud
Hi All,I'd to submit the following question to your great experience and knowledge:we're going to integrate a VCS Control with X7.1 OS on board with a VCS EpressWay with X7.0.1instead.Is this going to work or will we need anyway to have matching OS/F...
Hi experts:I’m working on telepresence project and I’m facing some implementation issues first I will start list BOQ:Cisco EX90 (version TC 4.4.2)Cisco C90 (version TC 4.4.2)E20Quick set C20VCS starter Pack (version 7.0)I need to achieve the followin...
hi all,I am relatively new to cisco TP products.Apparently i am really confused on the difference between the very similar naming convention of the cisco TP products.Would anyone care to spell out a quick differenciation between them? Or is there a c...
Is it supported to install Windows 2008 and SQL 2008 for TMS 13.2
Hi Guys,we seem to be having issues with our mps when trying to register to our vcsc via h232. we seem to be experiencing the same issue with two seperate system controller blades. Mps registers no problem on sip. the vcsc keeps reporting that there ...
Hi,I`m wondering if Conductor could load balance video traffic around third Party MCUs like Radvision, since they are added into Conductor through H323 and SIP trunk configuration.Thanks for you opinion,Sergio.
We are getting ready to start using TMSPE, however first we need to disable TMS Agent replication on all VCS's via TMS. There is a VCS that failed and was subsequently removed, but we can't remove it from TMS because TMS Agent replication is enabled...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-22-2024 07:29 AM | ||
07-18-2024 12:19 PM | ||
07-07-2024 01:38 AM | ||
06-27-2024 06:47 AM | ||
06-10-2024 11:20 AM |