Hi Everyone, Just wondering if any one knows if the Cisco UCS B200 M6 Blade Server will work with the Mellanox Infiniband 200G switches (https://www.mellanox.com/sites/default/files/doc-2020/wp-introducing-200g-hdr-infiniband-solutions.pdf). Let me k...
Forum Posts
I have a C240M4SX. running windows 2012 R2 the IKVM works as expected. I upgraded to windows server 2019 and the IKVM now only shows the screen but no longer accepts keyboard or mouse input nor responds to macro commands. It still responds to keyboar...
Resolved! UCSM MIBs import into Zenoss
Hello, I'm trying to import the UCSM MIBs into Zenoss. However facing issue. Any idea what's wrong? Thanks /opt/zenoss/share/mibs/site/cisco/CISCO-UNIFIED-COMPUTING-TC-MIB.my:32: identifier `TEXTUAL-CONVENTION' cannot be imported from module `SNMP...
Hi Folks, I tried to boot from a USB my server B series. I insert the USB into a KVM dongle an set the policy as below Local FloppyLocal CD/DVDRemote Virtual DriveCIMC Mounted CD/DVDLocal Disk but didn't work.
Hi folks,in my UCS Cluster i have four Blade servers. Two B200 M3 and two B200 M4.The M4 servers have two adapters in inventory:UCSB-MLOM-40G-03 and UCSB-VIC-M83-8P.Now my question is:Should i separate my vHBA (fc0 and fc1) on two vCONs (four are sho...
HI all,According to the example of official website curl -GET https://10.10.10.10/redfish/v1/Managers/CIMC/LogServices /SEL/Entries\?\$skip=2\&\$top=2 -u admin:admin123 --insecureThe upper example code can get top two and skipping two records of sel ...
I would like to know if it is safe to delete SSH core dump files on Cisco UCS FI as sysmgr 100% FULL (nxos)# show system inter flashMount-on 1K-blocks Used Available Use% Filesystem/var/sysmgr 2048000 2048000 0 100...
Resolved! Operating System Support
I have a Cisco UCSC-C220-M3S server with Windows server 2012 installed in it and got a request to Upgrade the OS to Windows server 2016 or 2019 .Could you please let me know if this server hardware support the OS ? Thank you in Advance .Yusuf Basha
I'm attempting to upgrade ESXi nodes in a USCM cluster using Hyperflex Connect. Under the Upgrade navigation link, I select Upgrade. Then select ESXi, drop in the upgrade image (which validates successfully) and the vcenter credentials. It starts the...
Can C220 run ok with one failed hard disc if the other discs are ok? at what point is this a major problem, as am unable to raise an rma becuase of cotract issues till tomorrow?
I plugged the server to a power source, and after pressing the power button the server wouldn't boot.I tried to connect to the serial port to get more information and I got this screenshot:Any thoughts about how to solve this?
During a Hyperflex Installer deployment, during the Deploy Validation phase, I'm getting this message:vCenter Reverse Proxy Port CheckvCenter reverse proxy at x.x.x.x is not reachable. Verify vCenter rhttpproxy port is open and set to 80. The springp...
Hi Guys, I have one C220 M3 server with 4 500 GB HDD CC03 and I have one of them shows moderate fault, then I decided to replae that HDD with another one, but the new one is CCO2 FW version, my question can rebuild success? or need to be in the same ...
Hi All! I have some older C240 M3 servers that we are looking to repurpose for lab gear. I've been trying to research the spec sheet here, and it shows that the server has 5 PCIE 3 slots, 3 of which are x8 speed (of different heights). We are looking...
During the Hyperflex Installer, 4.5(1a) ESXi, I am getting an error message, "Error: Firmware versions were not fetched" on the UCSM Configuration page. This is after the selection of servers page. This results in the UCS Server Firmware Version fiel...
