HiWe have issue with connecting Fi to Nexus . 1 link is use for Fi - server and 1 link is for Fi to nexus . and configuration is : Fi to nexus : Fcoe vsan 100 and with ether channel , and ether channel and port is up and operational state is ok but ...
Forum Posts
HiI am trying to install hyperflex but i got this error: Configuring HX serversError occurred while configuring UCSReason: Server configuration failure. Success count: 0. Failure count: 3Configuration Failed
Hi,i have new hyperflex cluster to deploy and i get this error in deploy validation step,my current configuration :UCSM 4.0(4h)HX Installer 4.0(2b)UCSC 4.0.4hESXI 6.0 factory installedthanks.
Has anyone tried two 16gb sticks on the UCS-E140-M2 with newest firmware 3.2.6 ? Looking to find a way to get more than 16gb max, hoping a firmware update will allow more. Thanks,Joe
Hello,I have to reboot an UCS-FI-6296UP via this command:FI-A# connect local-mgmt bFI-B(local-mgmt)# reboot how long does the reboot take please ? Thank you.
Configuration Notes: UCS v2.1(3f) x4 B200 M2 w/ M81KR VIC (Palo) 4 vNICs provisioned per ESX host. 2 for Production traffic / 2 for Storage & vMotion (each are on separate vlans w/ no SVI, flat VLANs). Storage & vMotion vNICs: 1 connected to Fa...
adding more vHBAs to UCS Hi everyone,I'm trying to add a new vHBAs port because I'm planning to set vHBA(s) as passthrough from the Hypervisor to VMsWe have the following setup & equipment:1 x Cisco UCS 5108 Chassis4 x Cisco UCS B200 M5 Blades Server...
We have seen cases where customers experienced avoidable Hyperflex related outages because FI connected upstream ports did not have the correct spanning tree config. For Hyperflex related FI installs, Catalyst switches should have the "portfast" opti...
Hi, I'm looking for local disk encryption capability on Cisco UCS B200 M4 blade server.If it is supported I'd like to know what additional hardware components is needed (i.e RAID controller, Physical disk, etc...) on blade server.
Hi,Found that from UCS Fabric Interconnect there is a command to connect to nxos. After connecting to nxos some no of show nxos cli commands (available on Nexus 5x series) are available but no "conf t" works. However in the UCS FI cli guide there is ...
Hi Experts, I have installed the UCS PowerTool 2.5.1.6 and when I try to run the command ConvertTo-UcsCmdlet it throws me an error as below. The module are installed in C drive so can someone suggest me how to get rid of this issue. Kindly suggest a...
Hello Team, I am facing issues with the UCS Powershell tool. As soon as I type in the command Connect-Ucs -Name <UCSM IP> the tool hangs up. It doesn't ask me for credentials. I am attaching the screenshot below.Unable to connect to Cisco UCS and han...
Hi, I have a bunch of C220 servers connected to the FI's. The OS has to be reinstalled quite often on all of them but every time I have to reset CIMC server on every node manually, otherwise the installation fails. How can I reset the CIMC server on ...
Hello, We have 2 UCS servers with 32Gb of RAM in each of them, the current RAM is samsung RAM (32GB Samsung M393A4K40CB1-CRC Server RAM, Low Profile, PC4-19200 (2400), ECC Registered (RDIMM), 288 Pin, CL17, 1.2V) We need to upgrade our RAM now, and i...
Hi Experts,Here's the scenario.A user is using Active Directory to manage a number of AD sites, servers and storage clusters.The newest of these are two freshly deployed Hyperflex Clusters running Hyper-VNow the friendly manual tells me:The user type...
