We have an older S3260-M4 server. I would like to upgrade it with an M5 server module, but does anyone know if you can remove the array controller from the old M4 server and install it directly onto the M5 server module. We have about 128TB of stor...
Forum Posts
Hello experts, I am confused about something regarding MACs, I think I need some guidance seeing the big picture. Say our VM MAC is 111(for simplicity) and it is using vnic 1 in UCS(MAC 222) If I check MAC address table on FI I see 111 assigned to a ...
Hello,We've recently added a VLAN Tag to Two Ethernet Policies within Intersight. When we go to deploy the Server Template, the deployment fails and we're left with this message (please see attached pic). We've not changed the Storage Policy. There a...
Hello Experts,I have a setup with 2 sites connected using Nexus 95K (1 at each site) over a L2 trunk link. Each site has redundant Fabric interconnect (A-B) configured in end host mode. The fabric interconnects (A-B) at each site connects to single N...
What are the high-level steps to remove SAN storage that has been decommissioned? It looks like I just need to update the vHBA profiles for the Servers and Hosts by deleting the vHBAs that were tied to the old storage as well as just remove the VSAN...
All,Well I got my C200 M2 server's CIMC working. Now I have a straight issue... so I know I am overlooking something. I go to the BIOS Section and change the boot order and I have the following:DC/DVD, IEF, HDD, FDD, PXEProblem is... it boots to th...
Resolved! Inaccessible CIMC
Hello,C240M5 - CIMC is inaccessible. It won't do pong and the MGT port has link up. Bouncing the port from the switch ( N2K FEX ) didn't help. Tried "ipmitool mc reset cold" from the host running RHEL9 but that didn't help either. CIMC firmware lik...
Hi Folks, we are moving a UCS FI-6332 system from old Network switches to new ACI Leaf switches. As part of the physical move, we are also changing the uplink ports on the FIs: Previous ports being 10G/SFP port and new ones are 40G/QSFP. Now I know t...
UCSC-C240-M4S2Bios: C240M4.4.1.2f.0.1024230116Installed a new UCSC-SAS12GHBA card to replace the cisco raid card and now the fan policy is overridden with the error "12gb sas modular pass through controller present" informing me this is an unknow car...
Hello all, I know this is not a supported configuration but has anyone successfully installed ESXi 6.7 on UCSX-210C-M7? Thank you, Hugo
With Michael Petrinovic Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about the Unified Computing Systems with Cisco expert Michael Petrinovic. Any configuration or troubleshooti...
I want to reset the CMOS password. I'm curious if there are methods other than using the cmos-clear command. If there is any official documentation, I would appreciate it if you could share it.
Hi guys!I have a Cisco UCS mini with the pair of 6324 fabric interconnects. There were 3 servers, UCS B200 M4, UCS B200 M4, UCS B200 M5. They were booting from Unity 480f, ESXi 7.0.0. We have added the UCS B200 M5 server, had some iisues with vnics, ...
(C240 M5) In CIMC, there is an issue where the LOM option under the PCI Adapter tab is displayed as "Not Loaded." However, there are no symptoms or indications in the system error logs. Why is this happening?Should this be considered a fault, and is ...
The CMOS password for the C220 M4 is set, even though I did not configure it myself. I also executed the clear-cmos command, but the password is still present. When I press <F6>, it prompts me to enter a password, as shown on the screen. What is t...
