Hello, Our customer has UCS 6332 in a cluster. We would like to know if it is possible to Connect HA FortiGates directly to Cisco UCS 6332 using LACP Aggregate interfaces and Virtual Port Channels (vPCs)(full mech)? Thank You
Hello, Our customer has UCS 6332 in a cluster. We would like to know if it is possible to Connect HA FortiGates directly to Cisco UCS 6332 using LACP Aggregate interfaces and Virtual Port Channels (vPCs)(full mech)? Thank You
Hello,i recently got my hands on a Tesla P40 GPU that I would like to use in my C460 M4.The power connector has caused me a lot of confusion.as I understand it, the Tesla P40 makes use of a 12V EPS connector.the connector on the PCIe riser board also...
Hi there, I have been doing an extensive search regarding the compatibility of Cisco B-series servers with Nutanix, and I've found that it used to be compatible with B-Series M4 only, but now it's reached its EOL (https://portal.nutanix.com/page/docu...
Hi All, We keep getting the error detailed attached when trying to install ESXi 7.0.3 on Cisco UCS C220M7N even after upgrading the latter one to the most recent CIMC version 4.3(3.240043) using ucs-c220m7-huu-4.3.3.240043.iso. Has anyone seen the sa...
Im a bit at a loss. I have and older ucs system with b200 m5 blades. I am reusing those blades in a whole new environment due to hardware refresh. The new environment is managed via IMM only and there is no UCSM.When i go to deploy my newly created S...
Hi All When migrating from UCS fabricInterConnect6296 to UCS fabricInterConnect64108,When migrating from FI A: Primary / FI B: Subordinate to FI A: Subordinate / FI B: Primary (connect local-mgmt to FI A and execute “cluster lead b” ), and then perfo...
After upgrading UCS 220 M5 from 4.0(4b) to 4.3(2.230270) I can no longer ping the CIMC IP addresses outside of the current network. I can SSH to them from the VLAN and confirm the gateway is there. I had power cycled one for 10 minutes and it still i...
Hi all, I was after some help with one of my servers. It's been with TAC since mid-March but I'm not getting anywhere. Initial symptoms were - P_CATERR_N thrown in BIOS with server freezing - Cisco recommended firmware update - no fix - Cisco swapp...
Hi Folks, we are migrating UCS B-series servers from old Fabric Interconnects to new ones. Both the environments are managed by UCSM and use native fibre Channel. As part of the migration, we want to maintain the same WWPN on the vHBAs as the previou...
Hello,Most of the information is in the title. I have connected the Tintri device with the sfps that came with it, and tried SFP-10-SR-S, DS-SFP-FC8G-SW, DS-SFP-FC16G-SW= on the end that is connected to the FI. I added the VLAN to both LAN->LAN Cloud...
Good day, I have a Cisco UCS C240 M5S in which I am attempting to load a copy of Windows Server on. I can boot from the USB drive in Legacy Mode with no problems, yet I cannot find a proper controller driver so that I can see the installed drives/vol...
I upgrade ucs from 2.0.2x to 4.0.4 everything is fine , but After I click acknowledge reboot primary FI, all blades on 10 9 chassis rebooted at same time, and pass long time rediscover time, we lost all bussiness for 2 hour, because we need time to ...
How and Where to download ISO file of ESXI 7.0 version ?
Hi Team, I am getting error (F1259 and F1260) in UCSC-C240-M4SX. Please find the details below and please help me how i proceed further wit severity: 1faultnum: 19cucsFaultTags: 2cucsFaultIndex: 3573547266cucsFaultSeverity_str: infoentity_DN: sys/ra...
The question is pretty much in the title. I have tried multiple SFPs we have here, and I am getting SFP validation failed for an appliance port.Thank you
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-07-2025 03:02 AM | ||
05-07-2025 12:11 AM | ||
04-30-2025 01:15 AM | ||
04-21-2025 05:41 AM | ||
04-11-2025 01:36 AM |