This session will provide an opportunity to learn and ask questions about Cisco Nexus 7000 Series Switches and FabricPath technology. Cisco Fabricpath technology on the Nexus 7000 switches introduces new capabilities and design options that allow...
Forum Posts
Hello Cisco Community--I have four blades in a UCS chassis. All of them are B420-M3s and they are running the following firmware. BIOS B420M3.2.2.6e 062220160138. Board controller 12.0. CIMC Controller 3.1(21d). Each blade has a VIC 1240. I cre...
Seems I have gotten a number of S3260 that were misconfigured. They have 18 disks, that are all configured as JBOD. I need to convert/migrate these to individual, single disk, RAID0's [OS is RHEL7]. It seems the Cisco Services Ready Engine Virtualiza...
Hi, We are having performance issues between 2 blades in different Chassis, but both are in same vlan. Please let me know, whether communication will happen with Fabric Inter connect itself or will the traffic need to switch through Nexus 7k core/Nex...
Hi, UCS C220 M5SX BIOS: C220M5.3.1.3c.0.0307181404 RAID controller firmware: 50.1.0-1048 When setting the BIOS to legacy mode I am able to see the Cisco 12G MegaRaid Controller just fine, and I see the controller POST during boot. Once I move BIO...
My question pertains to the correct cabling & vSAN setup from the UCS FI to the San Switch (Cisco MDS).Currently my cabling is as follows:FI1 port 25 - SW1 port 3FI1 port 26 - SW2 port 3FI2 port 25 - SW1 port 4FI2 port 26 - SW2 port 4On the San Switc...
we registered a new ucs domain on ucs central. all options are selected as global. But the templates and policies are not showing in ucs manager which are created under the domain in uce central. UCSM Ver --2.2(8) UCSC Ver-- 2.0(1d)
how do I connect a physical port to a VM in UCS? I need to connect a physical appliance (NIC port) directly to the VM. Is this possible or can I map a switch port on the nexus directly to the VM?
We testing Hyperflex solution with hyper-v for our customer. HX220c M5 Servers HX software - 3.0(1d) Firmware package - 3.2.3g Our installation process failed on deployment step. Powershell deployment script created in ou=hyperflex in Active Director...
I can't launch KVM on a UCS c240 m3. I've tried multiple different browsers and multiple different computers. After launching KVM Java loads and gives me the following error: <?xml version="1.0" encoding="UTF-8"?><jnlp codebase="https://<ip addre...
Hey Guys I am trying to connect Quantum scaler I40 to my ESXi 5.1 host connected via FC. I am not very good with drawing yet I have tried best to present my setup. There are 2 drives in Tape library HP and IBM. After zoning ESXi host with tape librar...
Folks, Is it possible to deploy Hyperflex utilizing 1GB port on uplink switch ? Let say we deploy port channel on FI (4 x 10GB) to the uplink Regards Budi
With the recent update of our vCenter, there were a lot of storage errors. I spoke to VMware support and they mention the physical hypervisor does not have the latest BIOS. Our VM boots from a USB thumbdrive. After updating to the latest 3.0(4i), I e...
Normally if I receive CIMC errors I create a case to have a TAC review the issue and determine the problem. Unfortunately I have a test environment with some servers that are outside of support and simply try to use them until they stop working and r...
Hi all,, Customer has standalone rack mountable UCS-EZ-C220M3S server with VMWare 5.5. Server is connected through 4 physical interfaces to two 6800s in VSS (two cables to one and two cables to other 6800).On 6800s these ports are grouped into port...
