Can someone point me into some definitive VMQ configuration documentation that is specific to UCS?
I'm trying to set VMQs on 4 vNics but every time I reboot the profile, some of the VIF paths come up and some don't depending on the configuration of ...
Hi,We have the following setup,UCS-C <> N2K <> FI-6248 <> N9KIs the connection between FEX (N2K) and FI (FI-6248) must be an MMF cable, could we use single mode SFP+?I found below Cisco DOC about the uplinks connection from FEX to FI could only use t...
Hello all experts,I am trying to connect to a UCS manager using the credentials saved in a XML file. Here is how I am doing it :-1. Connect-Ucs -Name <Name>2. Export-UcsPSSession -LiteralPath c:\test.xml ( Specified the key as "ucssession" when it pr...
Hi,
I was looking for the Chasis 5108 bundle, we previously acquired the following P/N (UCS-SPL-5108-AC2). I have seen that the P/N has change to UCS-SPM-5108-AC2; but i want to be sure that the configuration inside is the same as the old P/N.
Thank...
I am looking for specific documentation related to the Nexus 9K (9396) and it's hardware ASIC layout per line card/module, does anyone have any information related to this topic to pass along? Thanks, Mark S.
Hi,I have just setup a chassis with 8 B200M4, each with 2 X 18core processors. I have observed temperatures of around 65 degrees celcius on some of the P2 processors while the P1 stay around 42 to 50 degrees. These are temperatures for blades at idle...
Good day everyone,
I have a a question recgarding Cisco Server BE6000, I have all my collaboration applications here and I was wondering if ther is any guide or special steps to take care if I'm upgrading the platform from ESXi 5.0 to ESX 6.0 ????
...
Hi, We have a Cisco UCS B200 M4. configured as an ESXI host with the ESXI O/S running on a single SD Card, we would like to add in another SD Card and re-configure with RAID 1 for redundancy. Does anyone know if this can this be done online and witho...
Cannot install the Windows 2012 R2 on local disks on a UCS C220 M3 server. Megaraid embedded Raid controller. C-Series managed by UCSM (2.1.3a)Windows sees the disk, but raises error message: cannot install on this partition.Don't suggest the usual a...
Hi,
Kindly when configuring SAN boot order, I have primary path for vHBA-0 and secondry for vHBA-1
Each can have 2 SAN Boot Target
So I can configure to max 4 Storage controller ports as targets
But we have DELL storage with 2-controllers. Each con...
Hi,
Kindly I have B200M3 and B200M4 servers
What if the AC power come down then come back
I have the resume-ac-on-power-loss set to platform defaults
But these servers don't have any preferable setting for this point in the Bios default
So do I ne...
Hi All,Having a performance issue with FCoE multihop from UCS.The layout is as follows:UCS 5108 Chassis --> 6248UP FI's --> Pair of N5k's (5548) --> EMC VNX 5300 2 port FCoE 10gig card x2Everything is functional - i can fc ping from n5k fabrics to th...
Hi all,
We just recently received a C220 M3 1.5.3b which will serve as a VM for Cisco servers. I am having trouble getting the machine to detect the hard drive I added. It is not even showing the hard drive in the boot option in BIOs. I looked at so...
I have noticed that a TFTP backup (full-state) from UCS-Central on version 1.2(1f) will not work as a restore, however if you run a local backup in UCS Central and download the file you can use that one to restore via TFTP
This is of course a proble...
