Ask Me Anything Event Welcome to the Cisco UCS C-Series Servers session! Whether you're setting up your first server or optimizing an existing deployment, this event is your one-stop destination for everything UCS C-Series. Our expert engineers, P...
Let's say that UCS System QoS has Enabled Priorities:- Platinum, CS5, 30%, no-drop- Bronze, CS2, 20%- Best Effort, Any, N/A% If a UCS QoS Policy called "MostlyBronze" is configured with "Priority: Bronze" and "Host Control: None", then all traffic re...
Hello, I have UCS system running firmware version 2.2(3e) and after applying additional four port licenses for each Fabric Interconnect, I got a warning message that fabric-interconnect entered grace period. We have these warning although we are not...
Hi, a want install Dialogic D/600JCT-2E1W PCI card into c220 M4. I'm looked up this card in spec sheet for c220 but not found it. This card compatible with server's pci slot or not?Thanks
When we enable VMQ in the service profile on a Hyper-V host. Do we also need to configure the VMQ to CPU assignment VIA powershell as described in the following? http://blogs.technet.com/b/networking/archive/2013/09/24/vmq-deep-dive-2-of-3.aspxDoes ...
Do the c240's support direct connection to the FIs using emulex cna or do they have to go through a fex? In other words, is direct connect (to FIs) only support using Cisco VICs?
I followed this guide:https://supportforums.cisco.com/docs/DOC-8582And it worked, but I have 2 problems.1) The blade being put into Standby starts back up immediately - almost like a reboot -and doesn't stay in Standby mode2) The Blade being put into...
what are the main differences between blade and rack mount servers?
Hello, I need a little help with a poblem I'm having with ethernet during fabric failover with the UCS 5108; I have a fairly vanilla infrastructure (attached image); 2 Nexus 5Ks layer2 northbound of the 62xx fabrics, the fabrics are port-channeled an...
Hi Team, I want to connect the EMC storage and Data domain on fabric interconnect, Is it possible to do that if yes then how? Regards
Hi all, I have my UCS manager and I need to make an upgrade, my questions is the VMs I have running do I need to move them from one device to other? or I can do the upgrade with no down time? Can anyone give me a procedure about how I have to do thi...
Hi!It seems that both B series as well C series have board controllers. What is the purpose of the board controller?We have the BMC/CIMC to provide management of the server and read the sensors. The CMC to operate as the "control plane" of the IOM in...
I have a number of UCS C220's and from what I understand you can monitor CIMC via SNMP, but my question is, what do you use to monitor? I've had 2 hard drive failures now where the only indication was alarm & amber lights. I'd really prefer to find...
Hi: I have a Cisco UCS B200 M2, UCSM 2.2(3e). I just created a new vlan 400 (BKP_192.168.6.0). When I proceed to modify the vNIC Templates to add the newly created vlan 400, I receive the following warning message: Modify VlansYour change:Create: N...
Hi, I am trying to add Cisco UCS C200M2 to Opmanager (monitoring tool) with no success. Just want to know the configuration on UCS box.1. do we need to have an acc with admin proviliges to login to CIMC?2. Does UCS support SNMP v2 or we need a separa...
UCS suffered a major melt-down today with both fabric interconnects deciding to reboot. As far as I know I have no HA policy set which would cause a fabric interconnect to reboot on its own. A similar error is on the other fabric interconnect. My ...
