Hello,We are implementing the hyperflex stretched Cluster of HX240c M6 All Flash Node,5 hx-servers at DC , 5 hx-servers at DR & 2 edge server for witness VM.now our DC site & witness site is ready to configure HX server, But DR site is not ready.so c...
Forum Posts
Resolved! VNIC in INIT state
Hi,VIC 1455 installed on C480 M5 UCSM managed and running RHELAll of a sudden, one of the host eth interfaces ( trunk VNIC ) gave up .. i.e. stopped responding and "enic" drive tried to reset it as it considered it as "hang" as well. Rebooted the hos...
I'm having an odd issue with a server (standalone C240 M4L) where the SAS SSD's are working fine, but using SATA HDD's causes TERRIBLE performance, and getting a bunch of "Unexpected sense" errors in the storage log, before it marks the SATA HDD driv...
Hi All, With more and more ransomware targeting ESXi, is there a way to disable SSH and enabled Lockdown on Hyperflex nodes without affecting it?
I have the following vSphere 6.7U3 host hardware running under UCSM. The host was built using the ISO " VMware-ESXi-6.7.0-14320388-Custom-Cisco-6.7.3.1":UCSC-C220-M4SName:Adapter1Model:Cisco UCS MLOM 1227PID:UCSC-MLOM-CSC-02Running Version:4.4(1e)Pac...
I've been booting my B200-M1 (and M2) blades from the SAN with no issues, but when I try it with the B440, it just hangs. I know it sees the LUN because when I boot from the install ISO I can select the lun as the install location. I'm also using the...
Resolved! Hyperflex and VMWare SCAv2 support
Does anyone know what Cisco's stance is with utilising VMWare SCAv2 on UCS HyperFlex?VMWare's HTAwareMitigation analysis tool throws warnings for the HyperFlex Storage controller VM's as they have "affinity to the physical processors" and tied to a h...
My C240 has a 2X Disk RAID1 boot LUN, 6x disk RAID10 LUN and 4x disk RAID5 LUN. I've installed WIndows Server 2019 STD.In Windows Computer Manger, I can ID the boot drive, Disk 0, as the RAID1 LUN. But Disk1 & Disk 2 are both 2679.40GB drives and I'm...
I recently got a decommissioned UCS C240 M4 from my work for use in my homelab. I've swapped out some ram for known good sticks as well as the hard disks. Unfortunately the server isn't showing any signs of life other than the front panel lights whic...
Hi, I exported an Events log from UCS Manager: Equipment>Rack-Mounts>Servers>Server 4>[Events] tab > Export Note the way the time is diplayed in the GUI - the date/time clearly shows 02:07:37 UTC time on 2018-03-22. Here is the same raw record ...
I'm getting no where trying to get this server up and running because I can't find a way to allocate the RAID groups to the locally installed SSD disks.The server has the following disks in the following order:DiskSize (GB)196029603960496059606960796...
Hi, We are experiencing issues with upgrading our individual standard-mount rack blade UCS servers. We know of an interface on their Hyperflex that allows remote upgrades of UCS servers. Could someone provide any documentation with procedures for a s...
Not clear how this can be fixed for KVM console opened from CIMC
how we can migrate boot from SAN to Nvme on Cisco UCS B200 M4 (because we are planning to upgrade to esxi 7)
Hello, We are planning to replace the old fabric interconnects in our customer's data center. The plan is to buy new FIs but to keep the old chassics. According to the datasheet, the IOM module won't be a problem because the 6454 FI supports both Cis...
