Hi, We have a running C220 with a problem in VGA interfaceWe do RMA and the new server arrive We have ESXi with Vcenter, hyperflex VM and other windows server VMs running on the old serverIs it simple to move the HDDs to the new server with the same ...
Hi there, I'm looking to update the firmware on some old stand aloneUCS 220 M3S that are in our lab (to hopefully close off some CIMC security holes that were found) but when I connect to the KMV and mount the iso they don't seem to show up as a boot...
Hi Experts,I need a point of clarification, and if anyone would be so bold as to SHOW me a way to pove this point, I'd be extremely grateful.The point in question is the order in which a Hyperflex controller seeks the target information for a Read Re...
Has any other people experienced F0397 issue on FAN module of UCS C220M5? We upgraded all old C200 and C220M2 to M5 from 2019 for all global sites, but has been reported failure for 5 times after ~1y, some sites report more than one FAN module fail.
I'm working on migrating a UCS and I see that somehow the KVM of the servers have two IP addresses. One is from the service profile and the other says equipment derived. What mechanism yields the equipment derived IP address? I want to have only one ...
Hello, I am trying to upgrade the firmware on some BE6M-M5 servers. From what I understand, these are c220 m5 servers, but trying to apply the firmware regardless of the version results in a soft lockup as seen in the image. Any ideas what is wrong...
I am migrating a UCS from one data center to another. I found that the mac address pool and external mgt IP address pools have overlap. What I want to do is shut the existing blades. Remove the current mac and IP pools. Then I want to turn up the bla...
I am migrating from one FI pair to another. The current FIpair has a 16 port FEX module in them. If I remove all theEthernet connection from them, can I remove the FEXmodule from a currently running fabric interconnect? Andon the flip side can I inse...
Hello Experts, The customer's one B200 M5 Blades Status LED is blinking GREEN.Is there any estimated cause of this behavior? Best Regards,
Preparing to migrate a UCS from one location to another - I noticed that the ESX/blade management VLAN 101 is checked as being "Native". However if I look at the switch side of the uplink ports there is no VLAN 101 assigned to be native for those tru...
Running UCS 6232 16UP fabric Interconnects with firmware 4.0.2dConnecting a UCS C220 M5SX server with a VIC 1385 card in PCIe slot 1. Direct Attach.Making a policy for the server and attach it.Before attaching the server to FI, I had VMware ESXi 6.7 ...
I added the policy for firmware 4.1(2a) to my servers and the servers show the package. However the running BIOS is still showing 4.1.1. I thought perhaps it needed to be activated but I'm not seeing 4.1.2 bios is an option there either. Is there ano...
At some point, the primary changed from FI-A to FI-B. When checking logs in ucsm, no other logs are checked. Can you tell me when it was changed? CLI or GUI ?
Hello! This time, the UCSM with firmware of 4.0(4b) and the server with firmware of 4.1 or higher will be newly installed.Previously, the firmware of the new server was adapted to the existing firmware by applying the firmware policy, but as it passe...
When I went to download UCS firmware for upgrades I had three files showing: ucs-k9-bundle-infra.4.1.2a.A, ucs-k9-bundle-b-series.4.1.2a.B and ucs-k9-bundle-c-series.4.1.2a.C. But I also see packages ucs-dplug-5.0 one one and on another I see 5.0 and...
