intersight with ucsx-210c-M7 bladesUpdated successfully all the firmware on the blades to the latest starred version 5.2(2.240053) via intersightI assumed this would update the bios the servers as well.?when I boot the servers via kvm it shows a low...
Forum Posts
Resolved! IOM failover interrupted
Hi,Can someone explain to me, IOM will failover or not if any one of the l1 and l2 cables of FI is down.? Thanks
We purchased BE6K-M6 and VMW-VSP-STD-1A.I upgraded esxi to 8.0u2 and tried to apply the Vsphere 8 standard license, but an error window appeared asking me to apply the correct license. Is there any way? "Please provide a valid license key" From what...
Hello everyone, I have two C220 M5's with 1387 VIC cards. I can not for the life of me get these servers to connect to the switch at 40Gb and don't know if I'm missing anything. I can get them to connect to the switch with a QSA and 10Gb adapter. I a...
For our new M7 UCSX servers managed under UCSM, I created a Storage Profile and associated Storage Policy to take the 2 local SSD disks and make them a bootable RAID1 LUN. My setup is this: Storage Profile:Name: pro_sto_localAuto Config Mode: Unspeci...
This is a newly set up C220 with a new CPU, memory and drives. The server was running great for about a week. Then we started to do some setup things with ESXi and that's when the server shut off unexpectedly. After that the only thing the server doe...
Hello, I'm having some issues with separating traffic on my UCS. I have a Lab environment and a Prod environment. I'd like to have two servers in the UCS chassis be on the Lab net and 2 servers be on the Prod net. Both environments have the same...
I need to be able to copy the vLAN Groups from one vNIC Template to another using Powershell. I have the following: $UCSDomain = connect-ucs MyUCSDomain $cloud = Get-UcsLanCloud $oSourceTMP = (Get-UcsVnicTemplate -Name "SHD-ESXi-A")[0] $oTargetTMP...
I'm having an issue booting from a pcie m.2 card. The pcie card is showing in the bios but the ssd is not. If i boot off of a usb I am able to see the drive in ubuntu. Does anyone know how to get this working. If it matters the OS installed on the m....
Dear Cisco Community,I am working on a Cisco IF(Cisco UCS 6248UP) with a chassis (Cisco UCS 5108 AC2 Chassis), and after initial setup, everything working, but now I am stuck with this info that led to an error.Deploying Fan policy changes on chassis...
Do you guys know if it is possible to configure iSCSI Boot from SAN in CISCO C220 m7 stand alone, using intel NIC X710-DA2 ? we are not planning to use cisco VIC Cards. Im not finding any information related. Thanks.
Hello,I am studying for my data center CCNP, and I have the following questions:Normally, if you boot the UCS from SAN, you specify the Target WWPN in the vHBA either in the CIMC vHBA's Boot Table or in the UCSM Boot Order Policy. But what if I have ...
Hi,I have a problem with UCS FI-Cisco UCS 6454, after the power outage, I see this message in the photo attached,cisco UCS Login Error: Cannot login to UCSM from subordinate node. I have checked everything but still get the same error.The only thing ...
Good morning, Forum In the lab, we have two UCS M4 units with firmware 4.1(2k) and 4.1(2m) and I was asked to upgrade old 1G NICs with UCSC-PCIE-ID25GF (0x8086 / 0x158b / 0x1137 / 0x0225) units for fiber connection. The cards are properly recognized ...
How to use Hyperflex Sizer? Is there any proper documentations with examples?
