How do I name an FXS Port so that when a call comes in from that analog line, it will say DOORPHONE instead of FXSScott HuotariCreative Computer Solutions, Inc.
We are setting up a remote office with an sr520w and a spa525g2 phone to be used with the UC540 at the main office. Initial testing is good. The phone was registered at the main office first and now we are testing it remotely.One thing we noticed is ...
Hi I have instaled the system spa9000/sp400 and a WRV210 Wireless-G VPN Router andrecently I instaled another WRV210 Wireless-G VPN Router in another location of the same companyI configured the VPN between this two devices the question is, Can I ins...
I'm setting up a UC320 for the first time and have a SPA509G connected, but system will not discover/register phone. Phone display indicates downloading various .xml files, but phone never completes booting.....looking for thoughts. Phone is connec...
Hello.UC320 - bunch of extensions on SPA525G2;Reception phone is SPA50X with side car.Side car configured to "Pickup Individual"SIP trunk configured with DID's for extensions. SIP Trunk codec is G711a for use in UK.Incoming calls from SIP trunk, exte...
I have heard a few complaints over the last few months with Drag and Drop of the Phone Loads for SPA 5x5 and 525 models You CAN download new phone load like 7-4-6 from CCO and “drag and drop” the .bin file inside it (there is usually a readme and an ...
I connected a customers CP7940 to UC540 and did it not register. I reset to factory Default and still no registrattion. Tech Support had me check the firmward and I was told that it is MGCP and needs to be converted to SCCP. I was sent this link a...
I am trying to change button assignments on UC560 extension that has SPA504 with 2 SPA500S Side cars. When I change the buttons through CCA2.2(2) the system indicated that the data was sumbitted but I aslo get an error (attached) and the cahnges do ...
Hi, I have a SPA9000 woking fine with IP Phones. External and Internal calls. Outbound and inbound.I have no router in front, so no NAT or FW problems, SPA9000 is connected directly to a DSL Modem in WAN interface and then I have a Switch in LAN inte...
Hello AllJust wondered if anyone has any ideas about the following.We have a site which has 2 ISDN2e Circuits & have installed a 2 BRI Expansion into the UC520.We had a issue on Friday with inbound calls not working so a TAC was raised and a Cisco en...
Hello,I have DND performing strangely. A user has DND set on the phone. When a call comes in it can ring up to 11 times before forwarding to voicemail. This is a standard setup, Other users have also complained of this. Is there a way I can force DND...
We have a SPA8000 connected to a UC540. After about two days of working, it starts acting flakey. They have 2 phones and 1 fax machine. When the phones try to dial out, they get a busy signal. The fax can dial out no problem. When you call into...
We are trying to get attended transfer working with a SPA500s. Steps:Answer callPress Transfer buttonPress relevant button on SPA500s. Nothing happensWe have enabled syslogging and there is nothing produced in the syslog at all when the console butto...
We are putting together a proposal for a customer who has existing call recording hardware using analog lines. If we install a UC500 system, can it be setup to mirror calls via a built in FXS port? We would like it to mirror the output to the recorde...
Hello ,I'm making my first installation of UC500, and I configured the UC500 with my specific needs....(config) #debug vpm all I used this command bellow and shows me that the call arrives.but I am not able to interpret the results, but there is a...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
