I'm curious about this.. Is it possible to have 2 UC500s connected via VPN and have 1 side be able to use the trunks of the other side for outbound calls to certain destinations?
Hey experts,One of our client is asking to change their dialout prefix from 9 to another digit.. apparently they have mistakenly dialed 911 a few times...To do this, I am planning to perform the following tasks1. change the secondary-dialtone 9 to se...
Hi XW,I meet the same problem as yours. I do not use a 2-line phone, but a Brother mfc845cw phone, which use 2-cord line. The phone line just has 2 cords. When I plug this fax phone in line1 port. The fax phone can receive both line1 and line2 calls....
Hi All,I would like to know is it possible to connect SPA9000 with CUCM by using SIP Trunk ? How is the setting on both ?Or is there any other way to connect SPA9000 to CUCM ?I Cannot get any clue on the internet about this Really appreaciate if some...
I have a small SPA9000 based network that has four phones and a SPA400. Callers can successfully leave voicemail and I can check Voicemail from the phones. What does not work is that the message indicator light does not turn on when I have a message ...
Hi,I'm having a trouble with a 32user model. The UC powercycles from time to time. Any idea on how to start troubleshoot. I'm going to place a pc for logging with a syslog server.Thanks,Eivind
I am trying to get a UC520 to receive incoming calls with an ITSP.Outbound works fine.Per the carrier he states a 500 Internal Server Error. I have upload his info.Per other posts, I have read about fixing access-list 2 and the ip address that the c...
We have sip configured on our client's box. I was wondering if we could setup an outgoing calling plan where if i dial an international number specifically, it would not use the sip but go out through the analog line which would feed into vonage adap...
I have found a problem with the 7.1.3 Early Adopter pack. I discovered that the firmware for the 7940 and 7960 phones are missing from the 7.1.3 Early Adopter pack. However, I was able to copy the correct phone loads for the 7940 and 7960 phones from...
we are creating a localized manual regarding the spa525g, it came to my attention that it seems to be impossible to edit entries in the personal phonebookdo we have to enable something for this to be possible, or is this a feature missing on the spa5...
Hi,The following is the current dialplan on spa3102.L:20,S:7,(4163067274|9058861310|9058899296|(*xx<:@gw0>|[3469]11S0<:@gw0>|[2-9]xx[2-9]xxxxxxS0<:@gw0>|1[2-9]xx[2-9]xxxxxxS0<:@gw0>|011xx.<:@gw0>)I understand that if my sip registration is gone or po...
Hi,I am proposing a solution for a customer that requires 2 internet connections to provide 1 connection purely for SIP tunking (Voice) and 1 for general internet use, my question is can we deploy 2 internet connection to the UC520?
I have been searching through my show run config and cannot find anywhere these services are located. I am unable to get rid of these two services from my CME Service URLs and do not wish to see them. Does anyone know if this is possible? If so what ...
We are trying to setup an analog phone outside in the lobby that when the handset goes offhook it will ring a line tied to an ephone-dn on the receptionist phone - anyone have experience with this? Ideas on what kind of phone we need in the lobby an...
By default, is SIP disabled on outside interface?Ie. could someone connect via SIP and make calls?I remember some technote came out says it was enabled by default on routers.https://supportforums.cisco.com/docs/DOC-3031
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: