VPN

Hi all,I setup few vpn acces on my pix 506, all theses access are dedicated to roaming users who used the cicsco vpn client.Each user have his own ip local pool (one per vpngroup and one address per ip pool), we have a problem because when the user d...

I have a new 3845 with one PVDM2-64 and two NM-HDV2-2T1/E1 and two NM-30DM. I want to use one E1 on each NM-HDV2-2T1/E1 for voice and one E1 on each for the 60 digital modems is this possible. If so how do I config the controller for the modems. I c...

Hi,Is it possible to configure VPN Ipsec on a Catalyst 6500 without any service module (VPN or FW) ? I know performance will be poor but I have only few tunnels to configure ...If yes, Do I need a special featured IOS ? And which supervisor do suppo...

What VPN throughput can be expected with a 7206VXR with NPE400 WITHOUT VAM2+ ... I could only find specifications WITH VAM2+

Dear Sir,We are getting the following error on our Cisco 3640 Router.-Traceback= 6042E3C8 6042E604 6051EF4C 604B3084 604B31EC 604012BC 604012A8Sep 19 01:03:50 GCC: %SYS-2-MALLOCFAIL: Memory allocation of 12000 bytes failed from 0x60433164, pool Proce...

How do you set the default gateway? using hyperterminalip address outside 192.168.1.25 255.255.255.0the pix sets the default gateway as 192.168.1.25 but the gateway really is 192.168.1.1ThanksMichelle

Hello,My Cisco 2511 is repately in reboot process and the following message appear in console:Copyright (c) 1986-1997 by cisco SystemsSystem Bootstrap, Version 11.0(10c)XB1, PLATFORM SPECIFIC RELEASE SOFTWARE (fc1)and i can't do anything also for acc...

Hi, I am trying to establish a site-to-site VPN connection between a Pix515 and SonicWall firewall. I am able to get a tunnel up using an 1841 integrated router with an ADSL interface with the same configuration as the PIX. The PIX has other tunnels ...

I configured VPN 3020 using CA. Works fine untill authentication set to none under IPSec tab. When autehntication method set to Internal/RADIUS, VPN users no longer be able to connect, even they are not prompted for username password. If anyone could...

HiI managed to open a VPN connection IPsec on UDP (the client says it is connected) but I cannot ping anything. The weird thing is that I managed to open the connection and ping whatever i wanted when using a wireless network with the exact same conf...

Hi,Is it possible to limit a VPN client's connectivity via a remote access IPSec tunnel? For example I have host A connecting to my network via an IPSec VPN on a PIX firewall. I only want this host to connect to host B and not any other hosts on m...

Hi, could someone assist me in the correct upgrade procedure for a pair of PIX 535s in a failover scenario, without powering them down. The upgrade would be from 6.2 to 6.3.Many thanks in anticipation.Charles

Hi all,I've got this problem with most of my users using DSL connection. All work fine using dial-up. I'm using Cisco Router 1720 connected to Pix515. Client is using VPN Client 3.61.These clients need to access Exchange mailbox via thru VPN. During ...

I have been wading through posts about connecting remote clients using Cisco's VPN software to the PIX. I have set up VPN access to my PIX 501 unit however, I am unable to reach any of the servers on my internal LAN.I have read that you nned to do th...

Hi,Can someone please confirm this for me? Based on the following paragraph from "Cisco Security Appliance Command LineConfiguration Guide", you cannot use the appliance for VPN connectivity if you setup virtual contexts. It seems to be a big limitat...