VPN

I have the following scenario:Host1-Firewall1-VPNRouter1-(IPSEC TUNNEL)-VPNRouter2-Firewall2-Host2Firewall1 is a non IOS non PIXVPNRouter1 is IOSVPNRouter2 is IOSFirewall2 is PIXFirewall1 is NAT'ing 1-1 the address of Host1. VPNRouter1 is NAt'ing bot...

Hi,I want to establish a VPN tunnel from a PIX to a another IPSec gatewayin the following way:Local network: 172.16.22.0. This network should be natted to a globalIP, say, 202.125.145.31.Destination host: 10.253.96.1Remote Peer: 208.207.82.72Users fr...

Hello,I have nearly the same problem, what my friend has a couple of threads b4.At my customer's place I am using pix 501 witha small microsoft network with client server architecture having wins and dns installed. Checked vpn using pptp server with...

After using "Configuring IPSec with EIGRP and IPX Using GRE Tunneling.pdf" as a guide, I ran my config by the VPN group at TAC. Both the fellow I worked with and his lead agreed that it is unnecessary to use the loopback interface as the IKE peer, t...

Is there a link to pull down the lastest VPN Client? Do you have to be a reseller etc. etc.Thanks,Scott

I have successfully established a vpn connection to the pix. i get properly authenticated using MS IAS with the VPN. If I ping, browse whatever no packets seem to come back through the VPN LINK. The guys in the office (at the other side of the vpn ca...

I'm trying to customize the vpn client installation to include our company logo and to also automatically add the profile pcf. I've tried using the msi transforms and it works great once I complete the installation. However, during the installation I...

Hi,,, I have a PIX 515 (6.1) and VPN Client (3.5.1). The Pix only support DES. When I used the VPN Client (3.5.1) with SmartCards (Aladdin) the ISAKMP proposal is the 3DES CBC. This proposal is the only supported by the VPN Client with Smart...

Hello,I have an 827 ADSL router for a small SOHO LAN and a PIX 515 at the office. BellSouth is providing the DSL service, and I have a block of eight public IPs at my disposal. I currently have a functioning VPN (tunnel works, can ping both sides, pc...

I have four working peers, but can't get the fifth to work. If I swap one out and put the new (5th) one in it works, but not with the other 4 in place.. ArrghhhTIA Ade

I am getting 60% slower file transfer performance with 3005 compare to 15% with 3030 in peer-to-peer environment.Any advise to optimize 3005 is appreciated.thanks,Audie

I'v tried this configuration, I've connected a PIX 501 (remote office test) and a 3640 (hq test) using Ez-VPN, all is working fine except for routing, when the IpSec tunnel is up all traffic pass throught the IPSec Tunnel.I don't understand how to r...

hi.i have configured two VPN's in my 520 PIX, a VPN with encryption DES andthe another one with 3DES, but only one is working,,,,,,,,,,,,,each VPN has an access-list associated and the traffic must be avoidedof the nat process, so the statement"nat (...

I have a 1751 connected to the internet via DSL running a 3DES IPSEC image with the following config:crypto isakmp policy 20 encr 3des hash md5 authentication pre-share group 2 lifetime 3600crypto isakmp key test address 0.0.0.0 0.0.0.0crypto ipsec t...

I have a 3 site SITE-SITE VPN with one sitting as the hub and the remotes accessing each other through the hub. My problem is, one of the hubs can print to the core, but when attempting to print to the other spoke, the document hangs in the queue and...