Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Earlier this week I followed the Cisco instructions below to convert C9105AXI-B to Embedded Wireless Controller (EWC) as well as the YouTube VideoConvert Catalyst 9100 Access Points to Embedded Wireless Controller - CiscoConvert Catalyst 9100 Access ...
Hello Teamclassic case with DTLS handshake failure due to WLC doesnt trust VAP's MIC.vap-0#sho inveNAME: CW9178, DESCR: Cisco Catalyst 9178 Series Access PointPID: CW9178I, VID: , SN:WLC#sho inveNAME: "Chassis", DESCR: "C9800-CL Chassis"PID: C9800-CL...
Hi experts -I've tried countless things to get this to work diff baud rate, sent CTRL-BRK, long ctrl+breaks, ESC repeatedly, at 9600, 115200, etc. and it always skips the 3 seconds delay. And getting similar messages on the EWC that I'm running on on...
Dear team,We would like to explore option in Cisco Meraki where we could generate guest wifi password for external guest. Instead of giving plain password, we think about other way where guest can obtain valid generate password to login for internet ...
Hi guys,I have an access point (9130AXE-B) that can't join the 9800 controller on 17.18.1 version. Below is the AP output:[*03/25/2026 00:30:43.1078] AP image version 8.10.130.0 backup 0.0.0.0, Controller 17.18.1.8[*03/25/2026 00:30:43.1078] Version ...
I migrated APs from C9800-CL to another C9800-CL, but I still see them on previous controller as "NOT JOINED" under AP StatisticsAny idea how to remove them from previous controller database?
I ran into an issue where I purchased two C9105AXI-B units without realizing they require a controller. For my application I am looking to have two C9105AXI-B connect with each other and no other devices. I found the following article that explains ...
I've bought couple used 1852i Access Points. So, the question is how to obtain MobilityExpress image to run one of them as controller?
I am having an issue with the Web User Interface (WebUI) on a Cisco Catalyst C9300-24P running IOS-XE 17.15.05.When logging into the WebUI via HTTP, navigating to the File Manager shows a completely blank/empty screen. No file paths or folders (like ...
Hi All- I am moving from Prime Infrastructure to DNA Center and have discovered lots of little challenges in my day to day activities. Here is the latest one i cannot figure out. I have tried going in through the inventory module or by starting wit...
We have enabled IoT through the DNASPACE, and its current status as belowIoT enabledProvisionedGateway role assignedSpaces configuration downloaded Component StatusAP Join HealthyCAPWAP HealthyAP Certificate HealthyBLE Radio HealthyIoT Hardware Healt...
Hi Cisco,We understand this is a cosmetic bug and doesn't impact service.However, we'd like to inquire about the roadmap for its resolution. Do you have an estimated timeframe for when a fix might be implemented?
How can we consider this is a fixed bug while manual setting is required?In today's infra with SD-WAN everywhere, outages and incidents have been generated due to this bug. Manual setting could only act as a reactive action when there is a MTU blackh...
I have a specific 3802E that will stop allowing users to authenticate after a peroid of time and a reboot of the AP fixes it temporarily. The AP is running 17.18.4.201 and connected to a 9800-L-F running the same code: Cisco IOS XE Software, Version ...
HiWe are performing throughput testing using the IPerf tool with 1 client on 2.4 GHz, 2 clients on 5 GHz, and 1 client on 6 GHz. All clients successfully associate and obtain IP addresses.During simultaneous testing from a single Test PC, throughput ...
