Hello guys,I have to upgrade a wireless controller today and I am a little bit confused about fus version.I have the output below from sysinfo command:Bootloader version............1.0.18Field recovery image version.........7.6.95.16Firmware version....
Forum Posts
I have two 1815i at home, both ME capable and ME enabled.If I unplug the AP that is running as "slave" AP, then immediately all the clients move to the AP still plugged that is the master.But if I unplug the master, it seems to me that clients loose ...
We have an IPv4 and an IPv6 ACL on a few WLANs on a Cisco WLC 2504. Is the CPU on the WLC being used, or the CPU on the LWAPP? All LWAPPs are in local mode.
Hello, I am trying to setup a Cisco VWLC VM in Hyper-V, whenever I boot the VM I get the following: Version is: 8.5.140.0 Server OS is: 2016
Please let us know if we can use any alternate of power supply “AIR-PWR-B=” if yes the please share the PID of the same. AP : AIR-CAP1702I-D-K9
Resolved! New SSID no Signal Strength
Hey all,I have wifi network with 2HA 3500Series Air WLC and 14 1852 APs. I had 2 SSID one is 802.1x and one for certificate provisioning and everything is okay. Yesterday I had to create a new SSID with the same network as 802.1x but with MAB configu...
I registered 8832 wireless speaker phones to the call manager via a wired connection. I want to set them up to use wireless.I added the voice vlan to the trunks going to the WLC I configured the calkmanager wireless profile and created a new ssid fo...
Hi all,I have three controllers in Mobility mode. the Mobility Anchor is spontaneously flapping and I have tried to remove the mobility features and readd the peers. It was fine for a short time. Then after a few hours, it started flapping again. So,...
I would like to create an additional nco group called ncseng just like ncsoper and assign users to this group based on an LDAP role. What I have created so far is the following for web access and cli access:set nacm groups group ncsengset nacm rule-...
Resolved! cisco 1702i Access point
Hi, I've purchased a cisco 1702i AP. I need to use it as an autonomous AP and set it via it's onboard web server as I'm used to do with other "low cost" models and brands. Please let me know if it is possible and how to do it. I'm not sure the proces...
Resolved! AIR-CAP 1702i standalone, is it possible to use different DHCP pools with different interfaces.
I have WiFi AP AIR-CAP 1702. I can configure DHCP pool on it to activate DHCP server. Is it possible to use different pools, with different IP networks, for 2.4 and 5 GHz respectively?
Quick topology overview before I get onto the issue: I have a Catalyst 3560X-24P (switch 1) with ports 1-22 untagged VLAN 10. Port 22 is tagged VLANs 10 and 20 and connected to a 1815i running Mobility Express v8.5 with two SSIDs on the aforementione...
Resolved! AP's reporting high channel utilization
We had a wireless expert come in and use 3 different spectrum analyzer (very sensitive) and he's getting clear readings. For some reason the Meraki AP is showing that interference is crazy. We then moved it over to another spot where we knew interfer...
I have downloaded a new image to a virtual WLC but before rebooting the controller, I pre-downloaded the image to the APs.Some APs are getting the status None on the Predowload Status.During my investigation I found that those APs are not supported b...
Hi AllMy WLC running in code 8.3.112.0 lately having disconnect-auto join back issue. And from the log i found that LWAPP-3-REPLAY_ERR spam_lrad.c 42155 appears. This happen when we refresh the ipad and running in IOS 13. The authentication using WP...
