Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello,I have 2 Dell Force10 MXL10 / 40 switches that form a VLT domain. From each of these 2 Dell Force 10 switches, one port-channel configured in vlt peer-lag mode comes out and these two ports arrive on a Catalyst 4500 forming a single Port-channe...
Has anyone tried the MESH feature in the latest version of mobility express? I have tried this with 1852/1815/2800/3880 APs and the MAP only use single channel to connect to RAP no matter how I configure MESH. Is this by design/limitation/bug or the...
With the latest versions of WLC and ME firmware upgrade, the authentication to Cisco wireless Android app is no longer possible. Does anyone know if Cisco plans to fix this? This app was really cool to use when it worked. Thanks,
Hi,I have a 1117-4PWE ISR router running ios-xe version 16.9.2 which I am trying to configure as a stand-alone (controllerless) wireless AP. I've been referring to this document on the Cisco website but absolutely tearing my hair out struggling to tr...
Resolved! Aggressive Bandsteering MR42
I want to use bandsteering on my MR42 to make fully use of the 5GHz band. But I find it too aggressive when compared to my other AP, which steers the clients to 5GHz only when the signal is good enough. The MR42 steers the clients to 5GHz independent...
Dear All, My WLC is recently damaged and not accessible and when i checked I found it out of RMA Coverage so I was wondering if there is a way to transfer my license from the old controller to the newly purchased one.
Hi there!So, I have a small office wifi to manage. We have one AIR-AP1832I as a master AP currently running Mobility Express version 8.3.102.0 and a handfill of minion APs AIR-CAP3602I-E-K9, currently on 15.3(3)JD$ (I think the last digit is cut off,...
We are running 8.5.140.0 on a Cisco WLC 2504. Wired clients are using SLAAC by using router advertisement packets to give themselves IPv6 addresses, and IPv6 works. IPv6 on the WLAN doesn't work for some reason. This document talks about setting up m...
Hi all,My WiFi network suffers from constant deauthentications and disassociations. Sometimes I can't reconnect the laptop until I reboot the AP. Tried what was suggested in other thread which helped the guy but it didn't help me, which was disabling...
Resolved! Problems getting AP to join WLC
I am attempting to add a third AP to an environment. I have one of the exact same model connected to the WLC already but this one is having problems. Please see the output from below. It receives an IP on the same subnet as the other access points...
Hello!I am looking for a way to block specific devices from all SSIDs except one. We are running WLC5508s, and do not have ISE or Prime installed, so it would probably need to be contained within the 5508.Our use case is this:We have custom applicati...
Just wondering what I should configure on my switch. If the LWAPP does not run STP, maybe I should enable "spanning-tree portfast trunk" and "spanning-tree portfast bpduguard"?
hello all, I am now having a Aironet 1815m and the SG-350-28p on hand, and i would like to put them together for internal testing. I have tried to put them together, AP powered, and however it seems cannot get the IP.so i cannot go into the configur...
Hello,I have a Cisco 3702i AP at home connected to my Ubiquiti switch as a trunk. If I log onto the AP it can ping all my VLAN gateways so I'm please that works. I can see the SSIDs, but when I try and connect I don't get prompted for the password,...
Hello,we have WLC 3504 ios 8.8.120.0 + set of AIR-CAP3702I-E-K9From time to time, clients experience problems connecting to a wireless network. Two identical twin laptops can be a meter away from the access point and on one there will be everything O...
