Resolved! CCNA wireless prerequisite
Will my valid CCIE Written (400-101) qualify as a valid prerequisite for CCNA Wireless (200-355)?
Will my valid CCIE Written (400-101) qualify as a valid prerequisite for CCNA Wireless (200-355)?
Hello,i have two C9800-40 Controllers, both installed via image (.bin) in bootflash: via install add command. Now i have one who installed in bootflash:, boot system bootflash:packages.conf and the other one in harddisk:, boot system harddisk:package...
Im looking into having 40 Mhz channels over 2.4Ghz band, is there a way to have this enabled? Any suggestions?
Hi All, Recently we bought a 5520-K9 WLC and AP2802I-E-K9 APs, DHCP is configured on the Switch and AP is getting IPbut unable to ping or it is not discoveredplease advise
Gents, I have a weird issue with WAP371-E-K9 V01, fw 1.3.0.7In 5Ghz AC mode I capture pcap using "administration" -> "packet capture" and getting a lot of "IEEE 802.11: Malformed Packet (Exception occurred)" and "IEEE 802.11: Tag Length is longer tha...
I am trying to install additional AP license in controller but "Command" option is not showing under Management -> Sofware Activation section to install license also I tried via CLI and getting error " License Installation is blocked by secondary co...
Hi all, As in title, i've setted up a guest wlan, pointing to a guest interface that connected to a XDSL router with DHCP. My private wlan works fine, clients have an IP from my Win DHCP server. That i want to do is to enable only wan access for gues...
I have some AP Meraki, which get failed alarms in connection with gateway. I've done the hard reset (some work) Procedure: delete from Network delete from inventory unclaim claimThe AP apparently goes offline for 4 minutes.But it doesn't work, I have...
I need to upgrade some controllers form 7.6.130.0 to support new AP models. The original plan was to go to 8.3 but due a bug CSCvf76274 we put this on hold. The fixed version for 8.3 is still not available so I am asessing 8.5.120.0. Unlike older ver...
Hi we know how to configure port security on Cisco switch to limit some user on the switch port. In WLC/AP side, do we have command whose function is like: switchport port-security mac-address xxx.xxx.xxx" Thank you
What is the latest build for the MR 52 access points?
hello together, I'm currently make a PoC with the 9800 controllers at the customer. which way/interface/network is used for the raidus authentication at the 9800-cl? I have two 9800-cl under vmware in APSSO mode and the interfaces are configured: Gig...
We have several iPad devices operating in Kiosk mode, or guided access, connecting to a WPA2/PSK WLAN. These devices are configured to not go to sleep. We have the user idle timeout configured for 86400 secs on the wlan, and the session timeout dis...
Hi, I'm looking at some informatino about various 802.11ax/Wi-Fi 6 access points. I know that OFDMA works with "coloring" which I assume is the same as "resource units" when it comes to handling multiple clients at the same "time". So my question is ...
I have tried to configure HA with 2 x WLC 2504, after going through all step:- Create same interfaces on 2nd WLC with different IPs- Enabled HA SKU secondary unit on secondary WLC- Set AP primary Backup Controller- Set Primary Controller and Secondar...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-17-2026 11:43 AM | ||
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM |
| User | Count |
|---|---|
| 4 | |
| 3 | |
| 1 | |
| 1 | |
| 1 |