Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello Team, We are planning to upgrade controller code as per below. 7.6.120.0 to 8.5.151.0.7.0.220.0 to 8.3.150.08.2.121.0 to 8.5.151.0.WLC model - 2504 I checked release note of 8.5.151.0. But there is no suggestion how to upgrade from 7.6.120.0 ...
WLC 5508 Web GUI or management very slow to login - 5-10 minutes.From clicking Login to login pop up takes forever ...Once logged in it's quite quick.Thx
I just configured AP 1830 via firmware mobility express via the GUI and it worked. But after restarting the system, the device still broadcasts the default SSID "CiscoAirProvision" and the SSID that I made, so also I can't get into AP management.How ...
Resolved! Catalyst 9800 HA | Select Primary
Hi community, Is it possible to create HA redundancy and prefer a member to be selected as primary with Catalyst 9800 chassis? By default it is selecting lower MAC address. Then, trying to remove HA is not helpfull as I kept both chassis with same na...
Hi all,I've problem with a WLC 5520. few Clients an IP 0.0.0.0.Software Version is 8.5.140.0 Around 30% are not OK. The problem is, we are testing on our secondary wlc all AP are moving in Secondary WLC perfectly but the few client that don't get a...
Is there any OID for monitoring total count of WLAN and APgroups created on the cisco WLC especially cisco WISM2 Thanks Before
Resolved! Kensington Security lock MR20
Would you like to know Meraki MR20 and MerakiSpoiler (Highlight to read) support Kensington Security lock function?
Ran into a weird scenario..Have SSID that is security but no splash page required, if you auth correctly you can get on.iPhone XR added to network, blocked due to issueA few days later returned to normal statusNow, the iPhone connects to SSID, get's ...
When ever I do a packet capture on an Access Point Wireless interface, all clients are disconnected from the AP which is an MR45 running firmware 26.4. Anyone know why that would happen? I'm trying to diagnose abnormal traffic coming from a specific ...
Good afternoon! There is a problem connecting Cisco Proximity to VKS terminals. When Cisco Proximity starts, the program starts searching for the terminal but the connection does not occur, although the terminal is nearby, another device is connected...
I've been tasked with setting up Certificate based authentication on our wireless network. i'm close but am looking for advise from anyone who might have done this or something similar. we have a semi-complex architecture. One primary facility and...
Resolved! cisco wirelless controller Ap problem
Hi Friends I have more Cisco Ap(Air-Cap-2702 E-E-K9 int my company everthing is ok but i have 2 problem1) When some user connect to specialy one AP these users after 2-3 minute disconnect from wifi what is reason? 2.4Ghz and 5GHZ is active . i think...
Hi, I bought 3 1815i APs from my IT distributor and when I tried to set them up for my customer I found that there was 2 versions of this AP, one with a Lightweight firmware which needs a WLC to work and a one with Mobility Express which is autonomou...
estoy reinstalando en windows 10 la aplicación de cisco proximity y me aparece el error 2753.lo que ya hice fue borrar temporales del sistema y del perfil del usuario reiniciando el equipo e intente instalar nuevamente pero me aparece el error 2753 n...
I have a 2504 that will not light up. No leds on the front. Appears to have power on the brick. Question - can I use a ASA 5505 power supply on these too? They also have a 48V supply and the plug is the same. Just not sure if the + and - are the s...
