Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hello to all! I apologize in advance for bad english ... I would like to know if someone faced this problem: there is cisco wlc 5520 8.2.141 and external captive portal. we are trying to set up this bundle so that the client ONCE is transferred to th...
Hello, Many Windows 10 clients connected to a specific 802.1x SSID encountered duplicate IP message error in a specific context: going back to wireless network after few days or switch from wired to wireless network.Our WLC version 8.0.152 and 8.3.14...
We wanted to upgrade our WLC Software, but some of our hardware AP's are not supported anymore. We do have several 2600er models.Firmware 8.5.140.0 Released June, 2018 -> supports 2600 modelsFirmware 8.6.101.0 Released December 2017 -> does not suppo...
Hi All, I have a root bridge 2702 AP and 5 non-root bridge 2702 AP's. The root bridge AP is connected to the network physically. The other 5 wireless bridge to the root bridge. What I am finding is that some of the non-roots are up and associated t...
Hi Folks, I am in the process of moving from 8510 to 8540 wireless controllers, is it ok to backup the configuration from the 8510 and store it on the 8540 ? or better to do the configuration of the 8540 manually. Thanks Aous
Hi, we're deploying a demo network for a customer and after a few hiccups it seems to be running properly. One of the problems was an oversubscription of customers on a single GE link to the controller, which I seem to have solved by adding a new lin...
I am having issues adding additional AP's currently i have 15 aps no problem but trying to add 2 more and no luck , they do show under statistics ap join with ip addresses assigned but status not joined.also found this:Reason For Last Unsuccessful At...
I purchased a AIR-CAP2702I-UXK9. I am trying to prime the AP but the controller will not allow it to accociate because the Country is not set. Is it possible to configure the country via the CLI? Thanks!
ap AIR-CAP1532I-D-K9 not join with wlc 3504 showing error in wlcosapiBsnTimer: Feb 26 15:32:14.307: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:3224 Failed to complete DTLS handshake with peer
Hi,i try to setup a mesh network (bridge) to connect two building together. The mesh network goes up successfully but can't pass anything over the other building.Here is my setupWLC5520 version 8.5.160Two AP 1562D, one as RAP and one as MAP, both eth...
I currently have Guest wireless working and the setup is with Guest anchors. Clients can only connect at 54Mbps. Is it possible to get faster connection speeds? My setup is just like what is shown in the "Cisco Guest Access Using WLC with Anchor...
Is their a way to pull a report for up time over a given period of time for a WLC? Thanks All!
Hey everyone,I would like to create a guest wifi which can be accessed by using a free voucher. The voucher has to be limited to a specific amount of time (e.g. two days). The user should connect the device to a non-encrypted wifi displaying a splash...
I have a client where the previous network engineer put all the devices on a 10.63.145.0/24 subnet. I want to use the Guest Network on a MR series access point, but that uses a 10.0.0.0/8 subnet. I am guessing that there will be potential clashes if ...
Hi,tried it in an older Post, but believe no one will recognize https://community.meraki.com/t5/Wireless-LAN/WiFi-devices-disconnecting-all-the-time/m-p/43042#M6644I have got the problem, all devices connected to the Guest Wifi are getting disconnect...
