Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Redundancy using vWLC and physical 5508
Our customer has two virtual wireless LAN controllers configured as primary and secondary - this is a new centralized environment but hasn't any AP's associated yet. As part of a migration from a legacy environment, we need to move the APs from a 550...
Hello, I was wondering if it's possible to review the spectrums of both 2.4Ghz and 5Ghz at the same time using Cisco Spectrum Expert? Thanks.
Resolved! Virtual WLC and AP1852I/AP1832
Goodmorning Does Virtual WLC support AP series 1852 and 1832? Because in AP datasheet "supported Wireless Lan Controllers" feature, i can read only hardware WLC e non virtual model thank you
Resolved! Aironet 1815i in Mobility Express flooding gateway (unstable internet connexion and VPN tunnels)
Hello, I am newbie with Cisco Aironet product so I appologize if I did any evident mistakes for experts in this forum I am encountering a very annoying problem which I am facing with a Cisco Aironet 1815i. When it is running and pluggled into th...
Hi, I´ve had been verifiyng problems with the cisco aironet 1815. Almost every day they crash, it means i can´t comunicate with controller or ap's in the management interface, and before that i see the following message on the log "Did not rece...
Hi all, I do have 3 x AIR-AP3802I-E-K9 and a WS-C3560X-48P with a PS of 1100 W, capable of 802.3at.I can get the APs on the WLC, but they're not broadcasting, and clean air is off. After some troubleshooting, even if I configured the switch interface...
I'm not a wireless expert by any means, but I would think based on the document this should be a simple initial configuration. Going through the document 1815T Deployment Guide it says connect to router and then plug in to LAN3 and go to 10.0.0.1. ...
HI, Can a new 1850 AP join and existing Mobility Express Network, if there aren't any dhcp server in my enviroment to lease out ip for the new ap. The new AP details as below :- AP Running Image : 8.3.102.0Primary Boot Image : 8.3.102.0Backup...
Good day, I am looking for a way, CLI or GUI to change the syslog port from 514 to 1514 or other as our log server is not able to listen on 514. I've looked in both but do not see any place to change this. Any ideas would be welcomed. Thanks MP
Hi Guys, I have an issue where in a mesh network , the MAPs are connected to very far MAPs / RAPs with lower SNR. is there a way to configure minimum SNR for the MAP to start looking for a better Path ? also what is the interival that a MAP check ...
I need a wireless extender for our Cisco DPC3829. I don't know what devices are compatible with it and can't find any thing online. Can someone recommend an extender that will work with this equipment? Thanks
Hello, the new version of vWLC, 8.4.100.0, is possible to install on Hyper-V: http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn84.html#hyperv-vwlc But we can't found nothing about installation, like file to download...... Ca...
We are upgrading to PRIME 3.1 (from 3.0.3), and have to start using Smart Licensing ... What are the weights of tokens, for device types: unified access points, WiSM2 WLCs, WLC 2504, WLC 5500, WLC 8540 ?
Resolved! WLC Top Client Devices Timeline
Hi all, i have a 2500 series AP and i have the Top Client Devices list that show me how much traffic every client do. Could you please, tell me a way to know since when they did the traffic? Thanks, Alessandro
Dear experts, I had a weird behaviour in a customer site. I tried to upgrade to 8.3.133.0 with the standard version "AIR-CT5500-K9-8-3-133-0.aes" but I was stuck in "Writing new AP image bundle to flash disk" for a very long time ... After 45 mn ...
