HiWe are using a CW9166 Access Point managed by a C9800-CL Wireless LAN Controller (vWLC) running image C9800-CL-universalk9.17.15.*Through the vWLC GUI, underConfiguration > Radio Configuration > High Throughput,we reduced the number of spatial stre...
Forum Posts
Is there a problem with Meraki MR33 units? Most of our MR33 units hang and need to be reset to factory defaults to be restored. We don't encounter this on our MR44s and MR52s. We have around 300+ units of MR33's so this will be a big problem. Started...
Dear all,You all might be working with Meraki access for long time. I just want to know your experience how to start from basic to advance setup & configuration for new guy.I am new in the meraki wireless access point, have to do implement and config...
Resolved! C9800 Web Auth
Hello, I try create SSID with Web auth for my guest. When i select 'none' in Layer2 security and tick Web Policy in Layer3 why the SSID is not showing? If i untick the Web Policy in Layer3 then the SSID is showing with open authentication.
Hello,is there any news or a date on a roadmap when IPv6 will be implemented for meshed APs?It is very difficult to explain to a customer why a wired AP works fine and a meshed AP is a nightmare because resolved hostnames cannot be reached with IPv6.
New featureSupport for OWE Transition modeSupport for AAA accounting + Fast roaming (802.11r)Support for Mandatory DHCP + Fast roaming (802.11r)Support COA Support + Fast roaming (802.11r)Support for Client Exclusion Policies (Manual)Support for DHCP...
Resolved! Band Select
In wireless environment should we enable the 'Band Select' or not? Based on this document enabling the Band Select will make 5Ghz will more attractive so the client will try to join to the 5Ghz first. https://www.cisco.com/c/en/us/td/docs/wireless/co...
Resolved! C9800 Test radius server
Good day. Tell me why the radius server test command is not accepted? It says: Invalid input detected at.
Hi team, We are using the C9105AXI-S AP with the EWC image installed, operating in standalone mode. This is a new AP, but when connected to our current network, it occasionally gets disconnected, and the LED indicator flashes alternately green and re...
Hi all,As the title suggests - would we need to reboot a WLC or its AP's if we change the highlighted field? I've read the associated configuration guide and there's no mention of a reboot but wanted to ask those in the field.
I'm currently running an AIR-CT5520 with RTU licenses and planning to migrate to a CW9800M controller. Since the 9800 uses Smart Licensing, how can I migrate or convert my existing RTU licenses for use on the new platform? Any official migration proc...
I have a 9800CL qcow image running in Linux KVM. I have 3 ports from the NIC assigned to the 9800CL by direct attachment. They show up fine as gig interfaces. I can configure them as no switchport and communicate across the network. However, when I s...
Would anyone please help confirm the most suitable software version for the Catalyst CW9800M WLC that supports the following AP models?current 5520 WLC version (8.10.196.0)Cisco Catalyst 9120AXI-KCisco Catalyst 9105AXW-KAIR-AP1832I-Z-K9AIR-AP2802I-Z-...
Hi,We have connected a C9800-CL Wireless LAN Controller to a CW9166 Access Point using the image C9800-CL-universalk9.17.15.01.iso.What is the command to check the power or current consumption of the CW9166 Access Point via the C9800-CL WLC CLI or GU...
Hi all,I'm installing 9124AX units on mobile trailers, and I'd like to know if it's okay to fit the unit inside a cabinet and run patch cables from the unit to the antenna. Using LMR400, Length 15m.I don't see it being an issue, but none of the docum...
