Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hey guys our Cisco WLAN IP Phones 7925 and 8821 have a strange behaviour: they roam very frequently (about every 4-5 seconds) between access points on different floors - even if I am standing right beside the access point on the same floor. The mai...
Hi, We have several customers who use the guest anchor setup (in a DMZ etc) for their requirements. This causes a couple of challenges for us (as a WiFi provider) and I just wanted to ask the community experience on a few things. I would be very grat...
Helloi have a controler 3504 and they 28 ap joind but i want to knwo why : Monitor> AP joint Static > ===> it show only 8 acces point and not 28 acces point ?? please , i would what is mean that ??
Hi everyone, I have issue about a SSID mapping multi vlan in flexconnnect mode.I know there are some method for this:1\AAA override2\AP Groups3\Interface Groups(pelase tell me if it's wrong). I want to confirm if all these method can use for flexcon...
Hi, we have just installed 2 x 3650 (Cisco IOS XE Software, Version 16.06.05) in a stack and each switch has 390 watts of power available and we are only connecting 11 APs model AIR-AP280. however, we are getting the below error for some: %ILPOWER-7-...
Dear All,Hope you all are well. I have 2504 WLC having IOS 8.0.152. I have configured 5 SSID on WLC which are broadcasting Perfeclty fine. The problem is that when client connect to one ssid he is perfectly connecting but if he wants to connect to ot...
Against my better judgment, I decided to spec out a new 1832 model for a new site instead of going with the tried and true 1702 model, and as I suspected would happen, it's no longer straight forward to configure it for autonomous deployment. My netw...
Hi all, I have the problem that my APs wont join my WLC for some reason.On the DHCP server I can tell that all 4 APs get an IP address and I also can ping them but dont see them on my WLC.When I look at the WLC log I can see the following messages: *...
After an unsuccessful change of software, the access point AIR-CAP2702E-E-K9 cyclically reboots.There is no way to get to the command line interface.The mode button for some reason has become disabled.How can I restore the access point? console outpu...
Hellofrom time to time clients EAP cannot connect to three or four points out of 100. At the same time, clients WPA2/PSK can connect to the same points. After the reboot of the problem points, the connection is restored. On the rest of the points bot...
Hello everybody Want to know if Apple Homekit and Philips HUE systems will work well in combination with the Cisco WLC 5508 environment. Which mDNS / Bonjour parameters need to be set? Thanks Rene
Hi I have deployed a new SSID with FlexConnect local switching using PSK and marked FlexGroup WLAN to ACL mapping.My clients are able to connect to SSID, get a valid IP. But when I try to ping the device, the success rate is 10% only. Even if I try t...
HelloI have a question about toplogy mesh wireless cisco : RAP and MAPi want to know if Toplogie mesh wirless is need is need controller hardware or moblity express ME 1815i ??? i want link talk about the rules about mesh with AP 1815i moblity expr...
Good morning with everyone, please a consultation:I have a Cisco AP 2802I, which has come with IOS to work with a WLC, this WLC is a 2504, with IOS 8.3.140.0 level, it happens that this AP is associated with the WLC for a few seconds, and then it sta...
Hi Guys,I want to monitor the operational status (up/down) of the APs on my production environment. I expect my cisco prime will send notification if one of the radio is down, either deliberately or the radio becomes faulty. I already set the alarm o...
