Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! GUI connectivity issue in WLC 8540
I can't access WLC GUI (v8.2.151.0) . The Error Message is "the certificate is not trusted because it is self-signed. The certificate is only valid for 169.254.1.1 Error code: SEC_ERROR_UNKNOWN_ISSUER" Firefox version is 54.0.1 (32-bit) Please let me...
Hello Everyone, We have just implemented a solution at a customer wherein we needed 41 APs in a single cluster. The newer code 8.4.100.0 supports 50 APs in a cluster for 1800 APs and up to 100 if we have 2800/3800 series as controller AP. For some ...
Resolved! How add one AP to the two Group
Hello! I have two AP group of my Cisco controller 2504. First group is "Office" and second is "Guest". I need connect AP for two AP group. If I turn a AP to the first group, it disconnects from the other. How can I make the AP work in two groups a...
Dears,All our devices connecting to corporate SSID and Guest SSIDwhen connecting to Guest SSID all devices connect and been redirected to ISE Guert portal BUT APPLE devices just stays on loading page to Ise server page for guest portal and nothing ...
We got a project to provide WiFi coverage (Voice over WiFi will be perfect) in elevator cars in a high-rise building. This is a 59 floor building with 4 main elevator banks - low-rise (1-19), mid-rise (20-37), high-rise (38-60) and freight elevator (...
Resolved! APs replace without breaks
Hello I need replace old APs (with newer, different type) which are connected to the WLC, without breaks (or with very little time). There are 2 WLCs, one of them is active. I need to keep old IP adress plan and same VLANs. Theoretically I can inc...
Resolved! Cisco WLC 2504 HA (N+1)
Dear All , i have two WLC 2504 , i am configuring HA ( N+1 ) , my Question is that can we do Configuration Sync ? between Primary and secondry Controller . Thanks
I have an SSID setup for MAC Filtering. Under Security tab of my WLAN, then AAA Servers - Is there a way I can load balance between my Server 1 and Server 2? I have two ISE Servers but it seems the SSID will always default to the first and only try s...
Eu tenho uma acess point da Cisco, modelo AIR-CAP-1602I-T-K9 e gostaria de usa-la de forma stand alone, sem controladora. Me parece teria que fazer uma conversão, para AIR-SAP-1602I-T-K9, através de software. Alguém pode me ajudar ?
Resolved! Question on AP2802I
Hi Team, I have a access point (AP2802I) I am looking for autonomous IOS image for this device, when I searched in Cisco site I was only able to get light weight IOS. Thanks in advance. Regards, Saikrishna
We have procured Cisco AP3802E as AP3602E is End of Sale, we need to configure AP in Work group Bridge mode as AP3802E does not support Work group bridge. Which model we can procure which supports work group bridge and which type of Antennas we shoul...
Resolved! Can not get WLC to factory configuration
Hi we have WLC 4400. Now I cannot get into it. PC connected to the console port. I press Esc button once it boots. but i do not know why it still boot normally, It cannot show some lines where it gives some choices in order to enter initial configur...
Given below is issue we are facing:Phone A: Wireless G modelPhone B: Desktop 7975G model (CIPC)When phone B calls Phone A, audio is not being transmitted to Phone A. Phone B is able to hear everything phone A says clearly.But Phone A is not hearing a...
Hi, I have a Cisco 5508-12 wireless controller and I would like to change its licensing to "High Availability" so that automatic fail over into a secondary Cisco 5508-12 can occur. It is my understanding that the current per controller 12 ...
Does anyone know how to get into ROMMON for these APs so I can change the flash. It's currently set to Lightweight mode to work with a controller. However, trying to get it to Autonomous Mode to work independently. It's been a bit tumultuous as it...
