Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi, I have 25AP base AP count license I can join AP 4 only after remove will try again only 2 AP can joinplease advice meWLC code is 8.2.170.0AP1/30/2018 14:39:10.2585] Active version: 8.2.170.0[*11/30/2018 14:39:10.2595] Backup version: 8.2.151.0APW...
Dears, I have two WLC 5508 running on code 8.2. Recently we configured one as HA Secondary WLC. After this.. even when the Primary WLC is acting as primary when the users connect to Guest SSID, it redirect to the web browser page but with an error "h...
Hello, my client was having a legacy wireless network in a warehouse environment with ceiling height about 10m high , the legacy AP was 1242 with external antenna where the signal coverage was good and never reported coverage problems, however aft...
Resolved! Controller Not Talking To Prime Properly
I'm experiencing a weird problem. My SNMP string is configured right, but no information is being sent outside of the controller. It works just fine as far as traffic goes. However, when I upload the controller to either cisco prime or solarwinds NPM...
Hi. Do we need ISE in order to use RADIUS/TACACS+ authentication to the ME AP? Is it supported on the earlier versions like 8.3.102.0?
Hi Guys, I need assistance finding why I'm not able to access the WLC GUI. I am not able to ping the management interface IP address neither. Everything was working fine until I added EACL to my switch. So I revert the configuration to previous one b...
We have an anchored WLC with 1Gbps uplink, how many concurrent Guest client can it support with 1Gb uplink? Thanks in advance!
Hi,Im a newbie in Wireless Access Point so please bear with me, the company already have an installed and configured Aironet 1850 but they have issue as below:1. Client being kick to the network and rejoin after sometime2. AP lost then rejoin to ME a...
Resolved! Wireless Concentrator from LAN
We are currently looking at deploying Meraki MR AP's on our LAN with 2 SSID's 1 which will bridge to our corporate LAN and a second which we hoped to VPN the SSID to an MX in out DMZ. We can get the AP's to communicate with our dashboard and can conf...
Hi all I have an issue where by i have a few laptops have no network access when their on WIFI I can see they authenticate via ISE fine, they receive and IP via the DHCP but soon after I see in the NAM client history logs that it looses it WIFI ada...
Hello, have a god day! I have a problem with a wireless network, al the access Point model 1700i was joined to a WLC, but this Wlc was Crashed. My question is if I can re-join those access Point to the new WLC without press the reset button, becaus...
I am trying to verify if the AIR-AP2802i-A-K8 with Mobility express is capable of FIPS140-2. I found this article below which states Mobility Express and the 2802i are compatible as of 8.3, but I am unable to enter the CLI command for FIPS: config s...
Hello Experts, With CMX we can enable the location tracking of wifi enabled devices. However how about tracking the location of non-wifi capable devices, for instance the non wifi RFID tags. Is there any third party solution that I can integrat...
Hoping someone can help? We just purchased quite a few 1562E WAPs. We will be responsible for mounting and connecting them for outdoor and indoor use. Questions are: Outdoor-using AIR-ANT2568VG-N antennas (dual band) we must use antenna ports 1&2. Is...
Resolved! ZABBIX and WLC - AP Monitoring
Hello. We implemented Zabbix to our network recently and we'd like to monitor ICMP ping of all Cisco APs plus other items.These APs are managed by Cisco WLC. I managed to monitor WLC but I am unable monitor any of APs. Even not a ping. To be clear I ...
