Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi Folks, I have a problem with an AP that is not joining to the WLC. It said problems with the country code but the ap is UX mode. AP Model: AIR-AP3702I-UXK9 WLC Configured country Codes: VE (Where i am now) Attached: AP: Boot ap process. Sh...
After 2 days straight of research and troubleshooting I have reached a point where I am completely stumped and need assistance. I have a Catalyst 3850 switch running Denali 16.3.6. It is running as the MC and has 2 Aironet 2802E APs connected to ac...
In PI 2.2, I would go to Network devices -> Wireless Controllers -> Check the box next to a particular controller -> Click 'Configure' drop down box -> select 'Refresh Config from Controller'. I have not found the same thing in PI 3.1. Does it exi...
Hi, In cisco 2504 we created a guest network and authentication is web Auth. But it is not working on chrome. All other browser its working . IN chrome its showing an error. Please see the attached screen short. Product details below. Software Versio...
Hi Guys I need to know can we use Cisco AP as a RFID Scanner? If it can use as a RFID Scanner, then please mention what AP models and IOS versions can use for that. Many Thanks. Regards Oshaka
Hello, FRA is globally disabled on our 5520 WLC (8.2.130 code) On the other hand when we look at the APs list on 802.11b/g/n tab, we can see only for 3802I or E : or For other AP models, like 3702 or 2702 we have : Could you tell me why the radi...
I need to deploy an WPA3 enviroment for one of my custumers. i'm using a 1852 AP witch the last firmware.There will be an upgrade version that support wpa3?
Hi. I'm trying to research the following command: debug dot11 d1 dfs simulate Does anyone know if simulates a DFS event on an AP or does it more "emulate" a radar and send out a little RF pulse from an AP to neighbouring APs? I'm looking for a way t...
Hi AllAny ideas on the issue below would be much appreciated: 5508 WLC v7.6 code, with 4x 3702i AP's attached, 10>15 Wireless clients average on x2 of the AP's (the Cisco stats say these AP's should handle 128 clients if pushed to their max), the oth...
A problem occurs when trying to install a WebAuth certificate: TransferTask: Sep 19 10:04:47.389: Adding cert (7998 bytes) with certificate key password. *TransferTask: Sep 19 10:04:47.389: Add WebAuth Cert: Adding certificate & private key using pas...
Hi, for HA SSO following topology is being used: Core 1 is primary for spanning tree and HSRP VLANs used for SSIDs offered by WLC1(primary) & WLC2(stanby). WLC1 & WLC2 configured in HA SSO mode and connected via etherchannel to core switches. M...
Hi, I am planning an update to our WLC and AP's (2602s) and wanted to clarify the behaviour around the pre download function. We are going from 8.0.152.0 to 8.3.143.0 I know from both the GUI and CLI you can issue a command to pre download soft...
Hi, I'm replacing an existing network of autonomous APs with Cisco Mobility Express (v 8.7) using 2802i APs. We use a total of 3 BSSIDs on this network. For business reasons, we want certain APs to only include a single WLAN BSSID. Via the Mobi...
hello all,I am new in wireless , i have Cisco wireless controller 2504 for 50 access point, access point 1262 and switch 3560.i setup the controller correctly and i contect it to the switch and connect the AP to the switch.i can ping from the AP to ...
I have a warehouse with 3700 AP's all using only 5GHz with 2.4GHz disabled. In the warehouse we use both the MC3190 and MC32N0 scanners. I am getting a lot of complaints about network issues by users of the MC3190 scanners. When I run link tests t...
