Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Dear All, We have more c819 routers to use LTE. A few of them works, few of them not. On the failed routers we dont get IP. " CHAT3: Chat script lte finished, status = Connection timed out; remote host not responding" chat-scrip is the same as well:...
Hello, I have a question. I have two remote offices on VLAN 50 but not on same subnet. Both offices have AP flexconnect in VLAN 50. Office 1: 10.1.0.0 /24 Office 2: 10.2.0.0 /24 WLC is in office 1 with IP address 10.1.0.250. Wi-Fi users in office 2...
*Jun 13 06:17:05.715: AP has SHA2 MIC certificate - Using SHA2 MIC certificate for DTLS. *Jun 13 06:17:06.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.0.100 peer_port: 5246*Jun 13 06:17:06.331: %CAPWAP-5-DTLSREQSUCC: DTLS...
Good Day Our Customer network consist of a Cisco 8500 Series Wireless Controller with Cisco Wireless Release Version 8.1.131.0 and requested to migrate there current 1252 Series AP's on the WLC. As per the following link information "Table" the ment...
Hi, So far we've installed -K APs in our network, but for next part of project we've forced to APs with -H regulatory domain. I want to know what the side effect of multi regulatory domain is in my installation. by the way, in my country all the uni ...
Hi, How do we decode or understand client disconnected from the debug log or traces . What is the difference between disassociate and deauth Thanks
Hi i bought new Cisco 1832I AP to connect WiFi in my small office business. i have connect to D-link PoE switch to that AP and D-link Switch connected to my Netgear switch. i am waiting since long time to get SSID but couldn't see any ssid related t...
Hi i bought new Cisco 1832I AP to connect WiFi in my small office business. i have connect to D-link PoE switch to that AP and D-link Switch connected to my Netgear switch. i am waiting since long time to get SSID but couldn't see any ssid related t...
Hello all, I am facing an issue with AP. AP is formed cdp neighbor-ship with switch but not joining with WLC. I tried bouncing port, but no luck. Earlier it was joined with the WLC. Please help me to troubleshoot the issue Regards, Abhijith
Resolved! CIsco 2702 AP Blinking Red/Green
We just attempted to deploy several Air-AP2702i APs. They seem to associate to the controller fine but are blinking red/green. After research and reading the below link it looks like they were shipped with the universal/country code as UX. From my...
I have a cisco aironet 2700 when i go to the Web interface I get the following: Here is the image file. System image file is "flash:/ap3g2-k9w7-mx.153-3.JBB5/ap3g2-k9w7-xx.153-3.JBB5/"Cisco IOS Software, C2700 Software (AP3G2-K9W7-M), Version 15.3...
Resolved! can't activate vWLC 8.0
Hi all, I can't activate the vWLC 8.0. when select .lic file on install license TAB, I have this error By using CLI : I have this error 0/2 licenses were successfully installed0/2 licenses were existing licenses2/2 licenses were failed to installF...
Help me! I have Cisco 5500 Version 7.5 I log in using the admin settings But can not save save config Thank you
Is there any command to check Sepcific Access point interface 802.11b/g/ , Interface 802.11a/n/ac status from WLC? We can check it from WLC GIU but is there any command to check it from CLI?
Dear All, The Cisco 1832i datasheet mention "If 802.3af PoE is the source of power, the USB port is disabled". The power source we used is 803.2af PoE, but the access point seems reload unexpectedly. We change the power source to 802.3at PoE to res...
