Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi, I am looking for the mib definition file for CISCO-LWAPP-DHCP-MIB. https://www.cisco.com/c/dam/en/us/td/docs/wireless/controller/8-3/trap-log/b_wlc_traplogs83.xlsx I need to resolve a DHCP exhaustion trap in my netwok management system. ciscoLwap...
Hello, I am using an Aironet 1852e with mobility express to broadcast an employee network SSID. The traffic for that goes from the PoE port. Is it possible to broadcast another SSID with traffic from via AUX port? I uploaded a picture to show wha...
All I currently have a pair of CISCO AIR-CT2504-K9 V05 Wireless controllers with IOS AIR-CT2500-K9-8-0-121-0.aes. I have 9 AP's all model AIR-CAP1702i-A-K9, with IOS version 153.3(3)JA5 and Primary software Version 8.0.121.0 everything is working ...
I was wondering if a AIR-CT5508-K9 Wireless LAN Controller can handle super netting? If it does is there anything I have to do to the NAT. I have been looking at several documents with no information on this. I am trying to gain more addresses on my ...
I have Cisco WLC 2504 which has 10 AP 1852E joined , i installed license 5 AP successfully , when i add new Access point AP 1852E is not joined to WLC it takes IP address from same scope of 10 AP i access to this AP and i see this error [*04/11/2017...
In my WiSM Trap Logs I get a message:Client Association Failure: MACAddress:00:15:00:04:a0:34 Base Radio MAC:00:0f:8f:30:8f:70 Slot: 0 Reason:Unspecified ReasonCode: 1 In the Message Logs, for the same timestamp I get the following:[ERROR] apf_utils....
The Main Dashboard, Introduced in WLC Release 8.1 can be very useful; even for reports much better than the ones in Prime Infrastructure BUT ....... Where is the definition of the values, intervals, and sampling ???? Network Summary --- TOP WLANs...
Hello , I have a problem with disconnecting of few clients(mainly Windows and Mac clients)I´m using Mobility Express with 4 APs.There is WPA2/ AES, EAP security with radius. I made debug of one windows client, and it was disconnected when reassociati...
All ghosts and goblins are invited to join us for a spooktacular good time on October 31 at 8:00am PT for our next Customer Connection briefing on Cisco Wireless Solutions. You'll first need to join the frighteningly fantastic program and then regis...
Hi I'm trying to solve this problem: The authentication method in SSID "WIFI" is vía Radius, the users join the network correctly, but if the radius service fail the users are automatically disconnected... 1. In Wlans -> Edit 'WIFI' Advanced tab,...
WLC is setup as a DHCP server for a specific SSDI/VLAN. My firewall list the IP of the controller instead of the client. Can I change that so the firewall see the client IP so I can apply rules ?
I'm having some trouble communicating between an Epson wireless printer that has Airprint capabilities enabled and other iPhones/iPads on the wireless network. They cannot see the printer. What do I need to enable on the 1852 (Mobility Express) so t...
Hi,I am stuck with situation, where I need to get the autonomous AP to just authenticate with ISE EAP-TLS, is it possible?so far I am not able to get it working, and ISE authenticate logs says that EAP method is not allowed in allowed-protocol, at th...
Hello,I am trying to add a MSE 3300 to the NCS from the management console.The MSE is at 192.168.200.10 (eth0) and the NCS is at 192.168.200.7I am able to ping the NCS from the MSE. There is no firewall between these two.'msed' is up and running as v...
Hello, Is this MobileMark model LTM502AAKKCWHT180 compatible with ir829? We are wondering about GPS interference. Using all 5 antennas (2 RP-TNC connectors for Wi-Fi, 2 TNC connectors for cellular and the SMA connector for GPS) housed in this unit. ...
