Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi , I have an AP that functions on 802.3at (PoE+) but my switch (Catalyst 3750G 24 running OS 12.2, w/PoE ports) provides 802.3af only, so i got a power injector that provides AT and disabled power inline for port where my AP is terminated. but my ...
Dears, I have changed the lightweight AP to Cisco Mobility Express Autonomous AP, it converted successfully and I can see the Cisco Controller> prompt I want the these as an AP to work as an autonomous AP how I can get the configure terminal command...
Hi everyone,My customer has this OOOLD deployment where some AP1231 are still working they are upgrading part of the WLAN to LWAPP but may need to leave some AP in stan alone for a while.I need to configure a new SSID that needs WPA2 enterprise AES b...
Hello, We have an issue where a client of ours is running 1242 series AP's on their network with 4400 series WLC running 7.0.252.0 code and they have a few AP's that are randomly dis-associating from the primary WLC and associating to the secondary W...
Hi Everyone, How important is to configure AP-Manager Interface? In my current scenario, I have configured AP-Management interface and AP has joined to the WLC on that particular AP-Management interface successfully and working fine.. Now Cisco recom...
We have a branch office that will be converting their WAN access to different means of connectivity. They are currently using a direct fiber link to our HQ data center (which is a layer 2 trunk, tagging all VLANs and terminating them on a router in o...
After initial boot, the IW3702 Access point (configured as mobile WGB) has a Teal (light Blue) Solid LED rather than Green. The LED state Changes to Dark Blue after connecting to an access point and back to green if the Access Point is removed. in...
Hi, Is it possible to integrate Cisco WLC with active directory?? if yes then how? Customer does not want to install any additional appliance(so radius is out of question). When client clicks on SSID, it should prompt for ActiveDirectory username and...
Hi all, i have to implement a wireless network in a large space, 180mt x 40 mt, i think its ok cisco 2504 for controller, but wich kind of ap's i can use? I dont have special request... Thx all
I am currently deploying a combo of 1532E's (root and non-root) at some of my remote locations. The distance between units would be on average of around 1000 feet. Of the 6 locations that I have deployed this solution, only two have been of a non i...
Hi, We see quite a lot of "Radar signals have been detected". We have enabled uni-II extended, and theres no real pattern to where it happens, very random. Is this a message that appears on an AP that is operating in say channel 52, but hears it off-...
if it possible , how I can enable advanced routing that is located in setup tab on wireless router device at packet tracer....
Hello, guys I've been checking one of WLC and found that some of the ACL, which are currently getting increasing counters, don't seem to be applied on any of the interfaces. I checked all of them and none have the ACL applied. Where else could it be...
Hi All, I am facing an issue with the Cisco Mesh wireless deployment. We have around 45 Root AP's and 43 Mesh AP's and are split between 4 to 6 root AP's in each IDF. The issue is that though the Root Ap's are directly connected using fiber cable. I ...
peeps,wonder if any of you have seen this before, trying to join an 1142 on a WLC_SRE version 7.4. the AP can ping the controller and vice versa. In the controllers GUI: Monitor>Statisticc>AP join, I can find the mac of the AP that I am trying to ge...
