Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I just got a new cisco EPC3925 wireless modem and I would like to know how to use the USB port, and what to use it for. Thank you ---Posted by WebUser Patrick Ciantar
Hi Everyone, One of our customer WLC is configured with 2 ACLs.This WLC has 3 SSIDs. How can i tell which ssid used which acl in gui? RegardsMahesh
One of my housemates has had to borrow my wifi adapter to connectto UPC BB in my house which uses a cisco epc2425 cable router/modem.Recently found a Netopia 2247. Is it possible to setup the 2247 asa wifi repeater so my housemate can simply connect ...
Hello, I am in thailand and unfortuanly the provider proivide us oldie hardware... A Cisco EPC2325...Before with my WAG320N all is perfect between WAN and my NAS. I have NAS 192.168.1.200 with ftp access port 21. Normally in WAG320N I just specify th...
I have been told from Cisco engineers different results regarding WLC 5508 ports should be tag or untag situations. One think I know, might not be 100% correct, isIf WLC 5508 port is tag then the switch port should be configured as a trunk port.If W...
Hello, On my WLAN Controller i have two LobbyAdmin accounts and 2 WLAN's with web-auth.When i make a user account on my LobbyAdmin1 account on WLAN1, i can also see this account when i login with my LobbyAdmin2 account.Is it possible to seperate thes...
Hi,I have a wireless access point, how can i connect it to a layer 2 switch thorough it's layer 3 interface.what configurations do I need on wireless access point and layer 2 switch?If I want to connect this access point to a layer 3 port on a layer ...
Hi , Can you explain four way hand shake step by step in wap2 enterprise ? I read some document but I dont understand exactly why is derive PMK , PTK , PGK . isn't An hacker capture this value . Help please
I am trying to access my company`s files remotely from my samsung galaxy tab running on android. I have connected to the server using anyconnect, but have no idea how to actually access the files on the server. I am connected to the server, now wha...
Hii want to monitor cisco access point using SNMP .These WAP are controlled by two Cisco Controllers (In HA mode ‘Active/Passive)and the protocol used for Controller-WAP communication is CAPWAP . Is that possible or not Somtehin Else can we find an...
Hi,I have a WAP4410N access point. While upgrading its firmware i accidentally removed its power adapter. Now i am unable to access it via its default IP. When connected without an Ethernet connection, the Power light comes on and stays on. However, ...
Hi people. I'd like to know if the autonomous AP spend licences when they're registered on WCS. I'can't find documentation about that. Regards.
Hi,I have recently been tasked with upgrading our old Autonomous APs to LWAPs. We have a 5508 WLC at our Virtual Co-Lo and I am using Flexconnect to accomadate local switching and dhcp at our sites. I have upgraded over 50 APs and joined them to th...
I have a Cisco 4404 with a GLC-T (non Cisco) converter plugged in when I plug it into the Cisco switch no link led comes on if I plug the GLC-T into my laptop the link comes on. Is the problem most likely Cisco switch configuration Cisco 4404 configu...
Hai i want to convert cisco 2602e to autonomous mode.I tried using mode butting manuely using extracting archive.no success.could you please tell me which ios and ways to do that.Access point console says timeout,tftp i can see could not find file.i...
