Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
What's the best way to verify the SHA1 and MD5 Finger print of the certificate uploaded to Wireless controllers 5500 & WiSM?
HelloI need a heads up we did a site survey carrying around an AP1602 to do radio measurements. We thus have made a map of where to position the APs so as to have minimal signal strength of -70 dBm anywhere wifi voice terminals will be used.OK so far...
Good Day, I am using a 5508 Controller and Radius for Authentication users are complaining they have to authenticate twice to log in using there Iphones also on guest network wish is using internal db to authenticate is there something on the control...
HiI have a problem - I am part of a hunt group, which is desk based. However I have just asked for flexible working, which would mean having a softphone and being logged into a hunt gropu when working from home.IT dept are struggling with this. Pleas...
Recently, I was implementing a project in the dock.The environment roughly like this: 1.there was a fiber link connected 2 LAN between the 6509 and the 3750X before 2.now we want to add a wireless link (using two 1532E APs) to bridge 2 LAN (...
HiI am using Version 7.0.98.0 and I am facing problem that every AP impersonating itself not any other AP.The Message Text is: "AP Impersonation of MAC '00:11:5c:6d:a5:a0' using source MAC '00:11:5c:6d:a5:a0' is detected by authenticated AP 'g7-2ug...
Hi all,i have a 5508 wirless controller i'am traying to configure felexconnect but i didn't understand the Vlan mapping.plase what does it mean ?
Hello Team,We have the cwa on our wlc's working fine to ISE for guest wireless (using the mac filtering method). Only problems are that the guest portal page does not come up automatically, we have to "browse" to google or something on the iphone / m...
Resolved! Two Controllers in different locations
Hello, Our custommer has two controllers in two different locations. For certain reasons all of the APs are in Flex Connet mode.We want to implement a failover solution so if one of the controllers fails, the APs in this location to be able to regist...
Hi, why should have to choose cisco WLC and why can not go other vendor(Aruba).
I have configured the 2504 WLC multicast settings so that I can use airplay with Apple TV 2 which works well, but have not been able to get the IPhone Remote App or Apple Home Sharing to work. I have looked at the following posts to resolve the issue...
Hi Guys, Need you help to configure Flex connect. Not able to find any document which can describe this feature in full. Basically my setup is as below 5508 --> 3750 --> 3560 --> Access Point Few questions : I have vlan 400 as management vlan on my...
HiI have AD 2012, FreeRadius and WLC in our network. There is a problem with authentication but I have checked logs on the FreeRadius and on this end configuration is right. I'm looking for some guidance - experience/documentations etc. to be sure th...
Hello,Is it possible to lower the power draw on the Aironet 1552e AP (AIR-CAP1552E-N-K9) so it will run on a standard PoE device (IEEE 802.3af). The spec sheet for the AP says you need to either use the Cisco PoE injector (AIR-PWRINJ1500-2=).Is there...
Hi. I have a problem with a AP-LAP1141N-K9, when I connect by console, only see this all the time: If I connect the AP to my network and try to enter by console or WLC (I have a AIR-CT5508-K9) I can see this messege: I appreciate your answers and he...
