Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi, I have dhcp problem with our new AP:I add an AP to our LAN.I make a simple configuration with a WPA authenticate.I can connect some equipment to this AP and our DHCP give an address correctly.We use adptator to give wireless connection to old sta...
Hi, I deployed wireless for one of my clients. All services and the internet are working fine.Only problem is that while sending and receiving emails using Microsoft Outlook, there is a huge delay.Even mails as small as 10-15 KB takes a lot of time t...
Hello,I have a switch (SF300-48P 48-port 10/100 PoE Managed Switch w/Gig Uplinks) and I want to buy some APs (Cisco AIR-CAP3702i-A-K9) and a Wireless Controller (Cisco 2504 Wireless Controller). Is that working?Someone told me that I can use APs and ...
Saludos. Tengo dos Router (No 1) Cisco RV110W. Uno funciona como DHCP y comunica a la red local con el ISP. El otro Router (No 2) RV110W solo integra la conexión de dos impresoras alámbricas a la red wifi local. Por lo que los dos router fueron c...
Does the 3702 , 2702 and 1702 support full functionality in Autonomous mode? i know there was a limited Site Survey function but wondering if they have added full function for these APs?
Dear Team, I have 2 nos of Cisco 2504 WLC configured with 1 SSID each configured with different network address in same LAN. Cisco 2504 is connected to Cisco 2960 L2 switch--->Cisco 3850 L3 switch----->Cisco ASA firewalll--->Cisco 2951 router----> in...
Resolved! No Global Configuration Mode?
I'm sure this has something to do the RAM or Flash memory. This is an access point that's been sitting on the shelf and as far as I knew it was working. However, I can enter privileged mode but there is no "conf t" or configure terminal option. I ...
Hi GuysI'm new with wireless and I'm struggling to get the AP to get an IP address. From the switch the port connecting to the AP has the native vlan configured as 161. Do I need to change the native vlan on the AP?If so how do I change the native vl...
hello, I have found one incomplete air-br1310g-e-k9-r AP in my office, would like to test it, but I would like to know if I think properly - I need 2 standard RG6 cable - 75OHM with F plugs fitted on both end to send ethernet signal directly from pow...
Hello,perhaps a somewhat stupid question, but how can I generate and manage over the lobby Admin Guest acounts? A Looby-Admin was created on the 3850er switch, but how can I connect to the switch as a lobby-admin? Just as with the Airospace WLC does ...
we are converting a large number of AP's from autonomous to lightweight and will be using flexconnect groups on a 7510. The flexconnect groups also have flexconnect ACL's which we are using for redirecting NAC & posture traffic. We have tried pre-s...
I have 5508 WLC and number of 1041 APsSome of the APs OPERATIONAL STATUS shows DOWNTo test it I take that AP from its original location, bring to computer room on the same building and connect it to the same switch port via patch cableIts OPERATIONAL...
Network environment:2 AIR-WLC2106-K92 AIR-WLC2112-K97 AIR-CAP35202-I-A-K910 AIR-LAP1131AG-A-K99 AIR-LAP1252-AG-T-K9Cisco6509-EIf controllers and APs have fixed IPs manually set, is it necessary to inform:1. Primary and secondary DHCP Server IP on int...
Hi all,We are using 2 WLC5508 in an SSO Cluster and Cisco Prime Infrastructure 2.2.0to allow our customers as Lobby Ambassadors to create WLAN Guest Users.Now my question, is it possible for a lobby ambassador to create a bunch of guest users with th...
We have a site with a 5760 controller installed and we are trying to utilize a 5508 setup as an anchor controller at a remote sire for guest access. The mobility peer is setup on both ends and is up. The WLAN insterface is setup on both ends. On the ...
