Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi all, I am getting a continuous stream of messages like the ones below on my 2504 WLC. *webauthRedirect: Jul 22 23:05:25.275: %EMWEB-6-PARSE_ERROR: webauth_redirect.c:1477 parser exited. client mac= 54:ef:92:37:e4:30 bytes parsed = 0 and bytes read...
Hi, Now, i am facing some time zone issues with ISE 2.1. When i create Self-Registered Guest Portal, i can add our time Zone (Yangon). Then i change to Sponsored Guest Portal with my authorization profile, this portal is using default time zone (San ...
Hi, Request your help with the part number for WLC-HA I am using two WLC (AIR-CT5508-50-K9), which is running as independent controllers in the same datacenter. One controller has been loaded with 75 AP Licenses and other with 50 AP Licences. And a t...
Hi all, I have an Aironet 1140, it has been running without problem for some time with a single SSID. I recently added a second SSID and both can be seen and used by PC's, however the second SSID cannot be seen by apple devices. I've tried iphones, i...
Hi all who can help me... i need to know what is the cisco LAp compliant with the more high atex directive ..someone can help me ?? thx all
I have Access Point model Air-AP 350 Series deployed at one of my small site as standalone Mode. Running with below IOS. Cisco IOS Software, C350 Software (C350-K9W7-M), Version 12.3(8)JEA3, RELEASE SOFTWARE (fc2)AIR-AP 350 Series Corporate SSID conf...
Hi, I have ordered a AIR-CT5508-HA-K9. It doesn't pair up with an active WLC and there is no permanent AP license on that HA-SKU. I wonder whether I can do any configuration or perform software upgrade on the standalone HA-SKU? Thanks.
HI, Trying to enable web-authentication using LDAP on the WLC - 5500 controller (software version: 7.6.110.0). Getting following error message. Have already restarted the controller but the issue persists: *ewmwebWebauth1: Jul 24 14:11:40.408: #PEM-1...
HiIn our project we configure two wism controller In Each wism controller they are two controller Altogather they are four controller each wism module will support 150 APS in our they are 210 APS of 1042 model How can i make fail over for these four ...
Hello everybody, WISM 1 Slot 2 is not reachable via its management ip address. Only via service ip reachable. (WiSM-slot28-2) >show logging*nim_t: Jul 06 07:47:23.087: %SIM-3-PORT_UP: sim.c:9982 Physical port 4is up!.*nim_t: Jul 06 07:47:23.084: %SIM...
Hello I have 8 router cisco wap321 and I need to set a unique wireless network in a big area. (all of them with the same SSID) So the users can have a transparent network roaming between the routers so I would like to know which is the better way to...
Hi In our project we configure two wism controller and it is installed in 6500 series switch In Each wism controller they are two controller Altogather they are four controller each wism module will support 150 APS in our project they are 210 APS of ...
Hi community, I found out after one week of testing: My AP 1702i (autonomous, latest SW) doesn't allow my wireless devices (iphone, notebook) to reach some SSL/TLS sites like https://businesswebmail.a1.netorhttps://www.bawagpsk.com for example. Somet...
Hello, I have installed CUC, CUCM and CUCM IM&P (9.1) and a 2504 WLC. Everything is working fine but some users experimented choppy audio on the jabber for win 10 using the wireless network with the wired LAN don't have any problem. There is no trigg...
Hi, I am looking at deploying 1500 series AP's to connect multiple remote buildings. Normally we would fit dual devices to ensure redundancy, however our existing switches are none managed so I cannot change any spanning tree configuration on them. P...
