Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Need to create WLAN ID > 16
We have a 2504 controller running version 7.4.130. Need to create a new WLAN that is NOT put in the default AP group and broadcast on all AP's, but the 2500 is restricted to 16 WLANs, can only use ID's 1 through 16, the first 16 WLAN IDs are automat...
Hi support team, What is the meaning: CISCO ISE 5000 ENDPOINT ADVANCED + BASE MIGRATION LICENSE (L-ISE-ADV-5K-M =)?Is it mean:Capacity of to the number of users allowed entry on the wireless network at the same time?or maximum the absorptive capacity...
Hi Team,We having some issue with the wlc 5508 after configuring the initial setup it saved and ask for reboot but after it reboots again it is asking for the initial configuration again.It is repeating the same Please help on this issue.Regards,Arun
Have 1142 LAP AP's installed in each floor, All AP in One specific Floor are rebooting. After reboot most AP are joining WLC but few are unable to Join WLC. Logs in WLC shows AP has Crashed due to "Unexpected exception to CPUvector 2000, PC = 0x49D...
dear all, kindly guide me how to configure WLC 5508 internal DHCP per WLAN basis , i read the following document it is clearly mentioned that we can configure DHCP on WLC 5508 per WLAN basis. but i did not find the configuration per WLAN basis htt...
Resolved! Maps are not showing rogue details
Dear All,After upgrading prime to version 2.2 from 2.1, also MSE from 8.0.100.0 to 8.0.110.0 we are unable to see rogue ap, rogue clients, interferers etc.Only heat map is getting generated. CAS & WIPS services are showing 'in sync'
Hi teamwhar are the difference between SWAP1600-RCOVRY-K9 and SWLAP1600-MESH-K9 ios for AIR-CAP XXXThanks
WLC 2504 Software Version 8-0-110-02702e Access PointsI have configured dynamic AP management interfaces on ports two, three, and four with IP addresses in the same subnet as the default management interface. The APs won't associate with the WLC but ...
Hello network and Cisco gurus, I have what is probably an easy one for most of you...I was given a Cisco AIR-LAP1142N-A-K9 WAP and want to use it for my home Wi-Fi as my current router's signal range is pretty limited and doesn't cover my whole house...
I have 2 DHCP scopes set up on a wlc 5508, one for the AP's and another for a wlan, the leases for the AP's scope show up, but the one that the clients on the WLAN are on do not show up in the "show leases" is that a bug? normal?
Hello In the Autonomous Access Point CLI I want to do a backup the network configuration on the USBFLASH: drive using the command 'archive" same as on the router CLI but unfortunately USBFLASH: is not visible in CLI of the AP. Does anyone of you is a...
For some reason when we attempt to update the IOS of our AIR-SAP2602E-A-K9 AP's there's a decent chance that the unit will become unresponsive. If you console to it, the device will be in rommon mode. At this point we have to copy the image over v...
I am attempting to implement PEAP authentication using a Local RADIUS Server on an autonomous Aironet 2700 Access Point. The RADIUS Server GUI only has checkboxes for LEAP, EAP-FAST and MAC authentication, but the documentation says that PEAP is supp...
We have configured WLC 2504 as per attached diagram , everything is working perfectly except we are not able to access the controller through Wi-Fi connection , though we can able to ping the same .Kindly help us to resolve the same.We can able to ac...
I have telneted to 2 APs joined to the same controller.sh logging command shows each AP has a differente time which is different from controller time.The difference is about 2 hours.controller is syncronized with system's ntp.date is correct for cont...
