Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi,Am facing problem with Flexconnect with guest user. My scenario is i have local DHCP at remote site for guest but i want them to authenticate through central WLC.Am using Layer 3 web authentication. also the web authentication page is not popping ...
Hi All, can anyone help me sort out the issue with the wireless connectivity to the Sonos speakers and the HP wireless printers.except these two all other users are able to connect to the wireless network and working perfectly,I had a doubt on multic...
Recently I replaced my ISP equipment with a Linksys WRT 1900AC wireless router. When I did this I lost connection to my LAP1142 that acts as a repeater. I can assign a static IP address of 10.0.0.3 255.0.0.0 and use the GUI interface, but when I sel...
I have just purchase a Cisco 2504 along with two 2702i and one 1702i. The WLC works fine with both 2702i. Unfortunately, it won't locate the 1702i. I have just see that the problem could be that the 2504 is running software 7.6.120.0 and that I shoul...
Hello guys, Enable the option to log the packets matching the ACLCSCtq05396DescriptionSymptom:ACLs on the WLC do not have the option to log the packets being denied/permittedConditions:In the event that we need to see the packets taking the counter h...
HiI'm interested in the wired and wireless converged technology, but am skeptical of it's validity/longevity. Specifically, regarding the use of the 3850 as a controller. Does anyone use this and do you think this is the direction Cisco is going with...
Currently we have WLC 7.4 that uses ACS 5.3 for AD authentication.We have a lobby account that create guest users. Is there a way to configure that overtime the lobby account create a guest user.That I would get a email notification Dash
I'm working on setting up a wireless bridge between two buildings that currently are connected via fiber. The fiber needs to be pulled back and re-run so we want to use the bridge as the L2 trunk while that work is being done. Right now I'm labing ...
Which command shows me the arp table for Ethernet data ports? What does the other table show me?
Resolved! WLC - Suppress DHCP Traps
Hi guys,I've recently changed my DHCP pools on my 5508 controller and am now plagued with traps this morning for the error: DHCP address pool recover. Scope: <scope>. I don't think there's anything going on that shouldn't be (?) so is there any way t...
I see an advice about we have reached 75% of clients trackin.It says that our license can tracking 7000clientes. Según lo que indica la web de Cisco la licencia del mse es ahora por APs no por clientes. No entiendo porque sale ese mensaje.In Cisco we...
Hello,I've got some problems with coverage on a site with 1602i AP's on a 2504 WLC. After some troubleshooting it seems that the 802.11b radio's are sending with a 16 dBm power output. However the data sheet of the 1602 says it can send out 22 dBm. I...
Hope this is the right place to ask, if not please tell me why it isint the right place. And if you also can direct me to the rightplace that would be much appreciated. Question #1What does it mean when it says "Cisco Aironet Controller Based"?Does i...
Hi Experts!I've configured the Profile Threshold For Traps on my Wlcs on both radio (I'm interested in the client threshold especially), the setting is 20 instead of the default which is 12. I've also configured the snmp traps to be sent to the Cisco...
Hi Team; I have two controllers, one is 4400 and the other one is 5500. Before the upgrade the redirection was working fine. We have upgraded 4400 to 7.0.250.0 and 5508 to 8.0.100.0. After the upgrade redirection is working only with 4...
