Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi,the following config works on AIR-AP1142N-E-K9, AIR-AP1242AG-E-K9 and AIR-AP1242AG-E-K9, but it works not on several tested AIR-SAP1602I-E-K9.The config is the same, except for "FastEthernet" replaced by "GigabitEthernet" depending on hardware, an...
I'm a Cisco employee so you can say I'm professional, but this really puzzles me: I have this Cat 6506 switch with SUP720 and latest image. It takes WISM card but not WLSM, the error msg being "unsupported". I'm using 15.1(2)SY3 image and used 12.2.3...
Hi all,I understand that it is possible to have the WLC send different NAS-ID attributes to the CIsco ISE so that I can create specific AuthZ policies based on that NAS-ID attribute.The only thing is that I cannot see anywhere in the FlexConnect AP G...
Resolved! Upgrade 2125 to 2504
Hello All, I have an envorinment with 18 APs wich are mostly 1242AG and one 1142 AG. I have a 2125 Wireless Lan controller servicing the network at this time. I have set up the 2504 wireless controller on a test network along with a spare 1242AG AP....
We have two Wism2 controllers running 7.3.10 and in the last 30 days they have both doubled the memory usage on the controllers. They went from 26% usage to 51% usage. Is there a way to figure out what may have caused this increase in memory usage an...
I have configured WLC NTP, time and timezone, however the Acess Point time got a 5 five hour difference, how I syncronize WLC time with AP time?thanks.
Recently a customer plan to migrate their old WCS to PI2.1. The issue is they are not upgrading the WCS VM. Instead they bought a new NCS appliance for PI2.1Has anyone tried to migrate the data from WCS to PI2.1 without migration process to NCS1.1.1....
Hello Allfor 802.1x authentication what should be the security policy confgiured on the WLC [WPA2][Auth(PSK)]or[WPA2][Auth(802.1X)]or?? hope to get some helpVR
Hi everybody: Some months ago , i had to upgrade our WLCs to the version 7.4.110, but the WCS doesn´t support these WLC ios version, then i decide to migrate to the NCS, i found some docs that explain that NCS v .20 supports these IOS WLC version, my...
In PI, there is Unique Clients Summary, what kinds of unique clients this report related to? associated clients, authenticated clients or other kind of clients?
Dear Team, I have Cisco 5508 wlc along with WCS. Kindly advise if I can install wIPS in my wireless network. Do I need to purchsase the MSE is mandatory for this wIPS installation. Regards,Jubair.S
Mobility 'Control and Data Path Down' between 4404 and 5508 WLC's. Hello, we have 5 x 4404 WLC's running 7.0.240.0 with mobility configured fine between them.We have installed a 5508 with HA running 7.4.110.0, and have tried to add it to the mobility...
Hi,OK, he is a intreasting one. I have a ASA 5510 which has been running fine (and still is). Not had any problems with devices etc. connecting to outside work and back.I'm trying to get a Meraki AP working to trial, however I'm getting something ver...
I have 4 red LEDs in the AP. how to upload the image to the AP.
I have 2 WLC's running in SSO mode, and I need to replace the Primary Box.I have the Redundancy Ports directly connected with a Ethernet CableI made a backup of the Primary WLC.And enabled SSO, with the same IP Addresses I have used on the PrimaryAs...
