Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I need to upgrade WLC5500 series to release 7.4.121.0, but at this moment, WLC manages two AIR-LAP1310G-E-K9, I´m not sure if after upgrade them still work.Are AIR-LAP1310G-E-K9 supported in this version?Regards,EF
Hi,We have deployed some cisco 2602-E access points in one of our clients place. The signal strength found in the laptops is very good, but the signal strength found in the smartphones is very weak and its fluctuating.What is the issue with this and ...
Hi,I am setting up wifi flexconnect solution and is a bit confused regarding what should be the default gateway for the dynamic interfaces which will be created. Will it be the same as the one for management interface or the will it be the one for th...
hi, I have problem with setup Cisco Aironet 702. I set all properties. Interfaces gigaEthernet and Radio0 are UP. I don't see my SSID in network. On properties for Radio0 I see error in section Transmitter Power. How can I troubleshooting this issue...
I can see many neighboring SSIDs in my WLC as rogue SSID and how i can manage this?
I have been trying to locally configure a username and password on a Cisco 3945K9 I am able to configure the username and password successfully...username myusername secret 0 xxxxxxxxxx but then if I perform a show run after I have done so, I get the...
hello guysI am currently designing a platform for a guest network, which must be isolated from the local network, the following equipment:ISE 1.2 (Cisco SNS- 3415-K9) WLC 7.0.230.0 (Cisco controller 5508)---> wlc ForeignWLC 7.0.230.0 (Cisco controlle...
Hi All, I have Configured DHCP snooping and IP source guard and Dynamic arp inspection on my 3560 and 3750 Network Switches,on both of them I'm facing that issue. (the printers and access points are configured to get ip addresses via DHCP), but when ...
Hello,What we are trying to do:John logs on to wifi using RSA fob for password. RSA sends back auth request with attibutes to WLC 7.4 that magically knows how to interpret the attributes and puts John on vlan 10. Mary logs on with her fob and gets pu...
j'ai besoins d'aide pour la configuration en autonome de l'AP 1600.
Hi all,I upgraded MSE today from 7.2.110.0 to 7.5.102.101 using the release notes, after the upgrade I get the following error:[root@ukgrelg-174-mse init.d]# /etc/init.d/msed startStarting MSE PlatformStarting Apache HTTPD ServerStarting Health Monit...
Checking to see if there is a way to control how the inside controller load balances to 2 anchor controllers. I was told its connection by connection, but wasn't sure if its true, and if that could be changes to a particular hash or something.Thanks...
HiWe've just purchased the a VM Version of MSE (L-MSE-C3-W25) installed on vSphere.Have followed the guide, gone to add this to WSE and it wont connect.Looking at the console it says to type /init.d/msed.start, I get -bash: /init.d/msed: No such file...
Hi,In my environment there's a 5508 (firmware 7.4.110.0) and ap 1600 with a ias radius server. All wlan are in flex-connect local switching, one client try to connect on a wlan but not receive ip address. After enabled debug aaa all i took the log c...
Resolved! IOS Root and WGB Connectvity
Hi Experts,What are the implications of blocking band 3 between a WGB and Root using the "dfs band 3 block" command. Note, this is enabled by default on IOS AP's as stated below. Does it in anyway affect the use of 802.11n MCS rates?http://www.cisco....
