Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi! I have a WLC 5760 where I want to create an AP group in which I can customize the data rate and radios to use in this group. For example, I would like to have an AP group where there is an SSID called "Production" where I can configure only the s...
Hello All, I need to apply an ACL in WLC 5508 such that it would allow https traffic on management interface only from selected clients. For same, I have created an ACL permitting only the intended users while blocking the rest. Have applied the same...
Hey everyone. I'm trying to setup a new SSID for a new VLAN on my controller, but I've run into an issue with DHCP. I'm unable to get any leases; however, if I setup DHCP on the controller as a workaround everything is fine. My controller resides on ...
Hello Team,Need your help asap...Customer has 2 WLC(2112) in their network.WLC1: 10.169.90.29/24 (mgmt interface)WLC2: 10.169.95.29/24 (mgmt interface)8 AP are registered to WLC1 and 8 ap are registered to WLC2Customer needs a seemless mobility when ...
WLC: 5508switch : Nortel 8300 (POE supported , not POE+)AP :3702 E In local mode everything works fine but after configuring to flex mode initially it works but few times ap disassciates from controller, switch port still lies up In prime : throws a...
Hi,Daily between 12:00 - 13:00 all users unable to connect to Guest Wifi. It seems like a policy/setting on WLC, but I don't know where to find these settings.Please advise.Thanks,
Hello everyone. I've got an Cisco Aironet 2602i with no image on it.I've downloaded the latest lightweight image to this AP ap3g2-k9w8-tar.153-3.JA1.tar and I was trying to uploaded via comand prompt.when I boot the ap it appears the following prompt...
We have a couple 5508 controllers (one in US and one in EMEA) and AIR-CAP2602I-E-K9 AP's. Our 50 branch offices (US, EMEA, and APAC) have 3750's but we are in the process of replacing these with 3850's. We want to provide a wireless network strictl...
Hi Experts, I want to achieve fail-over for anchor controllers which will be connected in two different data centers. One foreign -anchor controller set-up in one data center whereas other foreign-anchor controller is in other data center . lets say ...
We have a number of 1242 APs that were powered down and moved factory location, after about 2 weeks when they were powered up again (POE from 3750 switch) on 7 of the APs the Ethernet interface did not come up, on the switch we could see the power g...
Good day allHere is my scenario. I bought a Cisco 1841 with a HWIC-3G-GSM module in as a failover router for a very remote site in South Africa. I did the config in my lab where 3G/HSDPA is available. Everything runs good, get an IP from ISP and ever...
Hi I would like to upgrade my controller to 7.4.x.x and i have about 1500 AP's - just wondering once i upgrade the controller and reboot wil all my 1500 AP's have their software upgraded at the same time ? what is the process the AP's will upgrade t...
Hi I would like to upgrade my controller to 7.4.x.x and i have about 1500 AP's - just wondering once i upgrade the controller and reboot wil all my 1500 AP's have their software upgraded at the same time ? what is the process the AP's will upgrade t...
Can someone tell me what the command is to change the country on a 3602 access point (from the AP not wlc).Thanks
hi,I have deployed a wireless solution with a wlc 5508 with the ssid authenticating users on the active directory my problem is that users cannot be able to access Email from the wireless network which is on the same network as the lan but users on t...
