Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Is it required that the access points are in the same vlan as the management interface on a wlc 5508?
Resolved! Design question and recommendation
Hi Experts,I have an upcoming implementation and I need your advise/recommendation on how to do the implementation. Attached is the network design with the APs and SSIDs. The 2 offices will be connected by fiber and will be L3 connectivity. The WL...
Good Morning,We need to upgrade our WiSM's and 4404's to latest firmware release to support the 3500 series AP's. These devices are covered under a cisco contract and we have access to the software to upgrade these. My concern is our WCS, we need t...
Hi all,We have a cisco ASA 5510, cisco 3560 switch, cisco WLC 4400, cisco 2960 switches and other CCTV recording severs in our network. Today we have upgarded the intenet speed of 50Mbps leased line. we are getting downloding speed of 50Mpbs in LAN b...
Resolved! 3850 MC & Compatibility Matrix
Hi,Following question. I checked the Cisco WLAN Software Comatibilitäts Martix last version ( September 13 ) and checked the section Inter - Release Controller Mobilityto check the possibility to mix 5508 & 3850 switches. If I understand the documen...
I'm having an issue migrating my Cisco wireless AP's off of an old Windows Server 2000 DHCP server to a new Windows Server 2012 DHCP server. The issue is that the AP's actually move over to the new DHCP server, but they only pull a 1 minute lease ti...
Can interference cause a radio to reset? I'm seeing some interference being reported in the alarm logs. I've also noticed the radios reset as well. Can interference cause this or could there be a problem with the actual AP?Interference threshold v...
Hi all,The title says it all. According to the 5760 Configuring Application Visibility and Control guide only the following AP types are supportedCisco Aironet 1600 Series Access Points Cisco Aironet 2600 Series Wireless Access Points Cisco Aironet 3...
I just bought a Cisco Air-SAP 1602I-A-K9 and am trying to use the GUI to set it up. I can't even get to the GUI. I connected the RJ45 cable to the console on the Cisco side and the other side to the ethernet side of my computer and used the browser...
Resolved! APs failing after buying new ones
On a WLC 5508, which was already running fine, with APs of the 1042 and 1131 type, new access points (type 2602i) are added. Since then, the AP's often stop working. This happens with both the 1042 and 2602i types of AP. The 1131 APs have no problems...
Resolved! Unable to recover 1231G
I am working on a LAB and the AP i got is stuck in "ap:" mode. Please help me to recover this.Below log shows what i have triedap: ether_initInitializing ethernet port 0...Reset ethernet port 0...Reset done!link auto-negotiating....auto-negoti...
Hello all,I'm in the process of planning, designing, and deploying a new wireless network. This new wireless network will be for guest access only in residential buildings for the families of our patients that stay for an extended period of time. I...
Resolved! Cisco Prime and Maps
HiWhen you create a map in Cisco Prime and place the APs, does this effect in any way the RRM configuration on the AP's? or there power\channel selection?Or are the maps a purely passive tool?Thanks in advance
Hi All,We have a WiFi network which we were hoping to just be an extension of the wired network. Configuration is all done and connectivity etc.. is good.My problem is that file transfer speeds when on the WLAN are a lot slower that I'd expect. I kno...
Resolved! 2504 Uplinked to 2 switches
Hi Would someone be able to confirm that its possible to use 2 ports on the 2504 and connect each port to a separate switch for redundancy?So i have 2 seperate switches and would like to connect port 1 on the WLC to switch 1 and port 2 on the WLC to ...
