Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
i,I would like to install a web auth certificate on a 5508. Version 7.6.130Every time I get an error on web gui or cli like:Cisco Controller) >transfer download startMode............................................. TFTPData Type........................
I have an AIR-SAP1602I-A-K9 WAP and I am interested in configuring it for WPA2-PSK security for WAP access. I don't see a way to do this in the GUI, does this model support that type of security? Thank you.
Hi,Is Clean-air express supported on the 3650 wireless controller with 1602e APs? The Clean-air options on the controller are available but do not seem to be active. In the controller gui the Clean-air admin status is disabled and the Clean-air opera...
Hello I have several user's that are close to one of the ap's that keep dropping. I see no reports of user's connecting to the other AP having any issues?
I need a little expert knowledge involving the TX and RX settings on a 819HW. When I configure the antenna ports:#conf term(config)#int dot11 0(config-if)#antenna receive right left(config-if)#endAnd do a show run, I see the setting under the 'inter...
Is there currently a way to modify alarms related to interferences on a per interference level? I have looked all over and I can only find enabling or disabling them but not adjust them as granular as we would like. We have APs located all over the c...
Hi Everyone, We have an SSID that currently uses mac filtering on a 4402 WLC. If we change the SSID to use a new VLAN / Interface, do we have to re-enter the mac addresses to get them to apply to the new interface? Or will the controller software...
Hello,I have been tasked with the modification of several AP1262N and asked to do it without physical access to the devices (high ceilings, multiple obstacles, etc). I'll be in the building and can direct connect to the ethernet, but will not have C...
Hi,as I received an eDelivery for our license upgrade, I logged in online and received my PAK ID.Then I looked up the controllers sysinfo with its serial no (v7.3.101) and I filled in the online formular to receive mylicense upgrade.Then I upgraded t...
I have a 5508 WLC and have loaded a demo of Prime 2.1 and MSE 8.0.The NMSP status is showing as inactive in Prime and MSE and therefore the clients are not showing on the map I have loaded.Any ideas?
Hi,today I tried to update WLC 5008 to software version 7.6.120.0. Everything went ok, but when I tried to predownload images to AP, some of the AP's failed during the predownload operation. Predownload was completed successfully to all (36) AIR-CAP1...
Hi , A Simple query . As you all know , the cisco 1700 access points come with two 1GE uplink ports .( Primary and Auxilliary ). I was under the impression that i can connect both these ports to an uplink switch , to create a LAG.Is it possible ? or...
Dear Team, please help me regarding below quries. we need to cover 200mtrs open area using wifii access points.as per my project requirement there is one apartment which having openparking area at ground level and there is main gate which is 150mtrs ...
Hi guys,This might be a noob question, but i need to make sure of it.How many users ideally can connect to a single Access Point:a. AIR-SAP1602I-C-K9b. AIR-SAP2602E-E-K9 with AIR-ANT2566P4W-R AntennaWhat do i mean "can connect" is the ideal situation...
Have three new products on Test Bench:CT2504 WLC w/ver 8.0.100.01702i LWAPP w/ver 15.3(3) JASG300-28MP Switch w/ver 1.3.7.18 (DHCP configured on switch with Option 43.)(no DNS server available) All three devices can ping each other but thats as far ...
